G
G
G
G
D
Q
J
F
F
F
F
F
F
F
F
4
A1
2
D
G
G
G
G
F
F
F
F
D
C
E
G
G
G
G
E
X8
K
X8
Q
2A.
Two Adults Suggested:
On a carpet, or protected surface, attach
Upper Dividers(F) to the Lower Center Shelf(D) using 8 Flat Hex-Head
Screws(L), using 2 in each. Tighten with the Hex Key Tool(M).
2B. Insert 8 Metal Dowels(J) into the plastic plugs located underneath
Lower Center Shelf(D). Tighten with a Phillips Head Screwdriver.
B
Left Side Panel
Right Side Panel
Top Shelf
Upper Center Shelf
Lower Center Shelf
Bottom Shelf
Upper Divider(4)
Lower Divider(4)
Lower Back
Upper Back(5)
Metal Dowels(16)
Round Hex Head
Screw(24)
Flat Hex Head
Screw(8)
Hex Key Tool
Hooks(10)
Posts(12)
Post Screws(12)
Cams(16)
D
E
F
A1
A2
C
H
I
J
K
L
G
M
N
O
P
Q
NOTE:
A Phillips Head Screwdriver
will be needed for
assembly (not included)
E
F
F
F
F
G
G
G
G
A2
B
A2
I
I
I
I
I
H
B
C
5-Section Coat Locker
with Bench
Model # ELR-0634
Mount Laurel,NJ 08054 USA
www.ecr4kids.com
1
!
WARNING:
-
Adult Assembly Required.
Two
adults recommended.
- Contains small parts, sharp points
and edges.
- Do not stand, sit, kneel, climb, lean
or pull on unit for support.
- Never leave children unattended.
- Do not place unit near high heat or
moisture.
- Adult Supervision Recommended.
TIP
！
DO NOT FULLY
TIGHTEN SCREWS
UNTIL ALL SCREWS
HAVE BEEN LOOSELY
POSITIONED
。
BEFORE ASSEMBLING,
MAKE SURE THERE
ARE NO
MISSING PARTS.
Attach Lower Dividers to
Bottom Panel
1A. Attach 4 Lower Dividers(G) to the Base(E) using 8 Round Hex Head
Screws(K), using 2 in each. Tighten with the Hex Key Tool(L).
Attach the Upper Dividers to the
Lower Center Shelf
L
X8 X8
J
3
Attach the Top Section to the
Bottom Section
3C. Turn Cams(Q)
with a Phillips Head
Screwdriver until
locked onto the Metal
Dowels(J).
4A. Insert Upper Center
Shelf(C) onto the slots in
the 4 Upper Dividers(F) as
shown, until fully engaged.
I
I I
I
H
D
E
I
C
Version: ELR-0634.D.2010.01.02
4B.
Two Adults
Suggested:
Carefully
stand the unit upright.
4C. Slide the 5 Upper
Backs(I) into the grooves
between the Upper
Dividers(F) and into the
groove in the Lower Middle
Shelf(D) until fully inserted.
4D. Slide the Lower
Back(H) into the grooves
between Lower Middle
Shelf(D) and Bottom
Shelf(E) until fully inserted.
F
F
F
F
Attach the Upper Center Shelf
and Back Panels
3A. Lay the assembled Base(E,G) on its side. Insert 8 Cams(Q) into the
large holes located in the 4 Lower Dividers(G), using 2 in each. Make
sure the arrows on Cams(Q) point toward the holes in the closest ends.
3B.
Two Adults Suggested:
Position the assembled Upper Section(D,F)
so the Metal Dowels(J) attached to Lower Center Shelf(D) enter the holes
in the top edges of the Lower Dividers(G) as shown.
- If the Back Panel does
not slide easily into the
grooves, wiggle the Back
while pushing the panel
into the slot.
- You may also turn the
rear Cams on the shelf
above or below to unlock,
push the Back until fully
inserted into the slot, then
turn Cams to the locked
position again.
TIP:
