SAFETY OPERATING INSTRUCTIONS
OPERATION
Before starting work it is advisable to test
the work surface for the ideal
temperature to use. The table below
gives an indication of the likely heat
settings required but always start with
the low heat setting.
The distance between the nozzle and the
work surface will vary according to the
material being worked on but this should
always be at least 50mm (2”) or more on
either heat setting.
All applications, with the exception of
removing paint from window frames, can
be performed without using a nozzle,
however for best results nozzles are
recommended.
Suggested Ratings
Welding Plastic
Low Setting
Bending Plastic
Low Setting
Heat shrinking plastic
Low Setting
Paint Stripping
High Setting
Defrosting Pipes
High Setting
Removes vinyl
floor tiles
High Setting
Soldering
High Setting
Lighting BBQ’s
High Setting
Nozzles
The gun is supplied with 2 different
shaped nozzles, which can be used as
follows.
Concentrator
Nozzle
Directs a
concentrated heat
flow to the
work surface.
Ideal for removing
paint in awkward corners, crevices,
mouldings, beading or architraves.
Glass Protection
Nozzle
Deflects the heat
away from glass or
other fragile areas.
Removing Paint - General
Do not heat the paint for too long as
this will burn the paint, making it
difficult to remove.
1.Choose the required nozzle and fit
onto the heat outlet.
2. Hold the gun with nozzle
approximately 50mm (2”) from surface of
paintwork.
3. Starting with the low heat setting,
move the gun slowly backwards and
forwards until the paint blisters and
bubbles.
4. Immediately remove the paint with a
scraper or shavehook.
5. Aim to heat the paint just ahead of the
scraper so that you can develop a
continuous action.
Removing Paint from
Window Frames
WARNING – Glass can break easily
when heated.
1. Use the glass protection nozzle.
2. Ensure the nozzle is facing the correct
way to deflect heat away from the glass
before you switch on the heat gun.
3. Rotate the gun/nozzle 90º as you
move to horizontal or vertical bead.
4. Paint can be removed by using a
shavehook and/or a soft, wire brush.
Maintenance
Always allow the machine to cool down
and disconnect from the power supply.
The heat gun should be cleaned before
being stored away by wiping over with a
clean damp cloth.
DO NOT USE
CHEMICALS.
Ensure that the ventilation
slots are not blocked.
Trouble Shooting
If a problem occurs always switch off
the unit immediately at the mains.
My Unit fails to work?
Check the fuse in the plug is sound and
rated 13 amps.
If an extension cable is used it must be
fully unwound and rated at least 10
amps capacity.
3
TECHNICAL SPECIFICATION
Power Supply
230V 50Hz~
Max. Output
1500 Watts
Temp at Outlet
Position
1)
330°C
Position
2)
510°C
Weight
(excl nozzles)
765g
ABOUT THE HG1500
The HG1500K is a highly versatile electric heat gun
which can be used for many different applications,
such as:
l
Removal of paint
l
Defrosting metal water pipes
l
Forming and welding plastic
l
Reducing heat shrinking tubing
l
Soldering
TO OBTAIN THE BEST RESULTS FROM
YOUR HEAT GUN PLEASE READ THE
INSTRUCTIONS CAREFULLY BEFORE
USE.
HEAT SETTINGS
The Heat Gun has two settings:
1. Low heat - for use where the
work surface or surroundings must
not be allowed to get too hot.
Setting~330°C.
2. High heat - for faster heat up
time of the work surface where you
can also operate the gun at a
greater distance.
Setting~510°C.
Concentrator Nozzle
Glass
Protection Nozzle
2
PLEASE READ BEFORE USE
DO NOT
Touch the nozzle.
Change/rotate the nozzle while the
unit is turned on.
Leave the heat gun unattended
when it is switched on.
Allow children to operate or
play with the heat gun.
Carry the heat gun by the
mains cable.
Allow heat to be directed onto
the mains cable.
Use the heat gun as a hair dryer.
Restrict air flow from the
nozzle outlet or fan inlets.
Allow the heat gun to become damp or
be operated in damp conditions.
Use the heat gun close to
inflammable materials, heat may be
conducted to combustible materials
which are out of sight.
Apply to the same place for a
long time.
Under any circumstances aim
the heat gun at another person or
animal.
Use in presence of explosive
atmosphere.
Danger of burns - Always wear
a pair of heavy grade, non PVC
type work gloves.
Danger of fire or explosion if the
appliance is not used with care.
When changing the nozzle, switch
off and allow the accessory and
nozzle to cool.
Place the heat gun on its stand after
use and allow to completely cool down
before storage.
A hot nozzle can cause damage.
Before every use check the condition
of the plug and cable. If these are
damaged in any way do not use.
Repairs must be carried out by a fully
qualified electrician.
Always ensure there is adequate
ventilation as gases and vapours
may be given off when stripping
paint. Ensure that protective googles
and masks are used.
Poisonous or inflammable gases may
be produced when working with
paints (especially older type lead
paints), varnishes, plastics and
similar materials.
Ensure the heat gun switch is in the
off position when connecting to the
mains.
Ensure children and pets are
excluded from the work area.
It is recommended a RCD (residual
current device) rated at 30mA is fitted
into the mains socket for added
protection against electric shock.
This product is intended for
‘household’ use only.
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for
their safety.
!
G29 08 08.qxd:G29 09/05.qxd 6/8/08 11:20 Page 2
