Maintenance
Periodically clean the thread and o-rings
with a lint free cloth and apply a thin coat-
ing of EagleTac silicon-based lubricant to
the o-rings (not the machined thread).
Clean the battery contact, signal contact
(the gold coated pins and PCB contact
area), and machined thread with a lint free
cloth. Use a small drop of Deoxit red
cleaner solution (D100L series) to slightly
lube them for better conductivity and
smoother mode switching experience.
Color and diffuser filter
Kit model come with diffuser and color
filters. Replace the standard head with
the head (w/ o-ring installed) with
mounting thread, and install filter to use.
1) Replace batteries
2) Ensure tailcap is tight
3) Clean all conductive contacts
(see maintenance section)
4) Check battery polarity
Troubleshooting - Flashlight does not
turn on or fails to switch between
outputs normally:
“No Hassle” EAGTAC Warranty
For repair, replacement, or other inquiries
contact your EAGTAC dealer. You can also
reach our customer support via email at
[email protected].
We warrant our flashlights to be free from
defects in workmanship and materials. We will
repair, replace at our option, without charging
any product or part which is found to be
defective under normal use within 120
months from the date of purchase with the
proof of purchase.
Electronics, chargers and rechargeable batter-
ies are covered for a period of 12 months with
purchase receipt. Such repair or replacement
shall be the purchaser’s sole and exclusive
remedy under this warranty. Normal wear and
tear including batteries draining is not
covered, nor is damage resulting from modifi-
cation, misuse, abuse, neglect, faulty battery,
battery leakage, improper maintenance or
repaired by anyone other than EAGTAC or
authorized dealer.
Do not touch or attempt to clean the
reflector, as it will damage the reflective
coating permanently.
Instant Turbo output
At any output level,
press and hold
the
on/off switch for 100% output.
Release
the button to return to previous level.
Instant Strobe output
At any output level (even off ),
double
press and hold
the on/off button switch
for strobe output.
Release
the button to
return to previous level (or off ).
“Deoxit” is a trademark of Caig Laboratories, Inc.
Periodically clean
and apply Deoxit
red to ensure
smooth mode
switching and good
long term reliability.
Adjusting output level
Twist the head to select between three
output levels. You can pre-select the
desired output level
before turning on
the flashlight.
1st level
2nd, 3rd,
level
Hidden AUX. settings
With the head at tight position (1st
level), loosen to 3rd level and then
tighten the head at 1st level within one
second to enter AUX. setting. Repeat to
cycle through all settings. Turn off the
light or loosen the head to quit.
Strobe (I/II) Hi-Flash S.O.S. (I/II)
Beacon Lo-Flash (cycle)
To switch between tactical and regular
mode, turn on the flashlight at 1st level,
dial to 2nd level and then back to 1st
level for ten times within five seconds.
Tactical Mode
100%
10%
Strobe
Regular Mode
100%
40%
0.5%
Level
1st
2nd
3rd
How to prolong battery life
1) Do not discharge the battery com-
pletely. Recharge often. Li-ion batteries
has no memory effect.
2) When the flashlight is going to be put
in storage for a long time, drain the
battery capacity to 50% or less for best
battery life.
Battery tube extender (optional)
We offer 3 cells (3xCR123A) and 4 cells
(4xCR123A or 2x18650) body extension
tube for extended runtime.
Energy saving feature
Enabled by default, this feature
reduces output by 25% (or 10% when
disabled) after 200 seconds at turbo
mode. To toggle this feature, turn on
the flashlight at 3rd level, and dial to
2nd level and then back to 3rd level for
ten times within five seconds.
