This programming features is provide the owner to learn the new transmitter or set new PIN code into the system
memory. This system can expand 4 different transmitters, and comes from factory with two transmitters already
programmed into the system memory. The PIN code from 1 ~30 numbers is available to set into the system memory.
Whenever you want to add or delete transmitter code ; or set your own PIN code of the system, the produces are
as following:
1.
In Disarmed position, turning ignition switch from ON-OFF for 5 times within 8 seconds and stay in the OFF
position, siren will provide 1-long chirp to indicate that the system is in this programming mode.
2.During step 1. Ignition switch stay in the OFF position:
It's available to learn the new transmitter into the system by press any button once of the new transmitter, siren will
give 1-long and 1-short chirps to indicate the first transmitter code learn into the system memory. To learn the 2nd,
3rd,4th new transmitters, simply press any button once on the each transmitter, the numbers of siren short chirps
is according to the numbers of the new transmitters learn into the system memory .
Note:
To exit this programming mode, if there is no new transmitters button been pressed, and ignition not turn
ON, after 8sec. siren will give 2-long and 2-short chirps to indicate that the system has been exit the
programming mode.
3. During step 1 or step 2. Turning ignition switch to the ON position:
It's available to set the new PIN code into the system, siren will give 1-long and 1-short chirps to indicate that the
system is in PIN code setting mode, at the time LED will start flashing, the times of LED flashing is according to the
numbers of the PIN code, let's say you want to set the PIN code " 12", while LED flashing 12 times then turning
ignition switch to the OFF position, thus the new PIN code "12" has been programmed, the siren will give 2-long
and 2-short chirps and then LED will auto flashing 12 times as showing the new PIN code for the owner of final
notification.
Note:
During the LED flashing of the counting numbers, if ignition switch not been turn off, the LED will keep
flashing 30times and the system will auto exit this mode, siren will give 2-long and 2-short chirps, thus the
PIN code "30" has been programmed.
Note:
During the LED flashing of final notification, alarm will not allow to activated.
How to use your PIN code:
If the remote control has been lost or damaged, you can manually disarm your system by enter your own PIN code .
(
The system's factory-set PIN code is "6"
) Turning the Ignition switch from OFF to ON position, LED will start
flashing, the times of LED flashing is according to the PIN code numbers, while LED flash 6 times then turning the
ignition switch to the OFF position , the system will disarmed immediately and siren will give 4-short chirps.
Note:
Each cycle of alarm triggering is only provide one time to set PIN code, otherwise the owner must wait next
cycle triggering and then set PIN code again to disarm the system. If the owner forgot the PIN code number, must
use "Emergency reset switch " to reset the alarm system (please see "Emergency reset switch" ), after this
emergency reset switch has been activated, the system PIN code will resume back to the original factory PIN
code "6" .
Transmitter & PIN code programming:
-Valet mode:
If you are going to have your vehicle serviced, parked by a valet or washed you will want to put your security system
Into valet mode. To enter valet mode disarm the system and turn Ignition switch to ON position , then press
button + for over 5 seconds until siren give one chirp and LED light ON to confirm the system is in valet
mode. When the system is in the valet mode it can not be armed. The door lock and unlock will function as keyless
entry system.
To EXIT:
Turn Ignition switch to ON position , then press button + for over 5seconds, you will hear siren
provide 2 chirps and LED light OFF to confirm exit this mode and in alarm mode.
Note:
While in the Valet mode, each time when Ignition switch has been turn off, the siren will provide 2 chirps for
warning sound.
-Passive arm
(programmable)
:
If set programme mode to
"WITH"
, while turn Ignition OFF, then close the last door ,system will provide 2 siren chirp and
2 light flash and LED flashing fast to indicated that the system is in passive arming mode. After 30sec. The system will
arm by itself and LED flashing slowly to show the system is in arming mode.
This system also provide under passive arming with door lock or without door lock feature (please see "programme
mode" features. ) During the period of 30sec. passive arming, if a door is opened, Led will light on and it will re-passive
arming when the door closed again.
-Car Finder:
The system provide a feature to easy find your car position, simply press button once when in armed after 8sec.
The system will respond by 5 lights flash.
