Eagle 680022, Руководство оператора

Страница: 13 / 20

Eagle Solutions, ©2008, Tracker Operator Manual Page #12 Eagle Solutions, ©2008, Tracker Operator Manual Page #13
Daily Maintenance - (every four
hours of operation)
• Check oil level (use 10W30 or SAE30 oil
only).
• Check and clean recoil dust filter.
• Check and clean carburetor air filter.
• Check belt tension by pinching belt together.
Belt should deflect only ½” (13 mm).
• Make sure all components (pad holder, fuel
cylinder, etc.) are secure and tight.
• Check pad holder and pad daily (clean or
replace).
• Clean machine. If compressed air is available,
blow dust from machine and engine,
concentrating on the inside of engine shrouds.
Wash undercarriage. CAUTION: Care should
be taken to make sure engine is cool before
water is used to prevent warping and other
damage.
Weekly Maintenance – (every
20 to 50 hours of operation)
• All Daily Maintenance services.
• Change oil and oil filters at 50 hours of service.
Use 10W30 or SAE30 motor oil. Use of non-
recommended oil may void the engine warranty
(see engine owner’s manual).
• Check for loose nuts and/or bolts on entire
machine.
• Examine all propane fuel components for leaks
or wear. Replace if necessary.
• Grease wheels. Use one pump only of white
lithium grease. More grease than recommended
may push the seals and dust covers out, allowing
dust and other foreign materials to penetrate the
bearings, thus shortening their life, as well as
allowing grease to drop from the wheels to the
floor.
Monthly Maintenance – (every
80 hours of operation)
• Perform all Daily and Weekly Maintenance
services.
• Consult engine owner’s manual for the
following:
»
Torque head bolts.
»
Check valve clearance.
» Torque valve cover bolts.
»
Inspect spark plugs. Replace if necessary.
» Remove engine shroud and clean cooling
fins.
Quarterly Maintenance – (every
250 hours of operation)
• Perform all monthly maintenance items.
• Have engine checked by an Authorized Service
Center - including emissions check.
Propane Fuel System
Repairs and adjustments to the fuel system can
only be made by an authorized, properly trained and
certified service technician. Improper adjustments
will cause increased toxic emissions of carbon
monoxide and may result in carbon monoxide
Changing the Oil
1. The engine manufacturer recommends 10W30
or SAE30 motor oil. ATTENTION: Do not
over fill oil and never run engine with low oil
level.
2. Run engine for five minutes to warm the oil.
3. Make sure machine is on a level surface, with
pad resting on the floor. Place a container under
the drain and open the oil drain valve. Allow oil
to drain completely.
4. Close drain valve and add 1 quart of 10W30
or SAE30 motor oil. Check level and add if
necessary.
5. Replace oil-fill cap assembly. Hand tighten
only.
Checking the Oil Level
When checking oil, remove dip stick, wipe clean,
and then reinsert the dip stick into the engine.
Do not screw in for Kawasaki or Robin engines.
Remove dip stick and observe oil level as indicated
on the dip stick.
Adjusting Belt Tension
Tools required:
»
9/16” (19 mm) open end wrench
»
15/16” (24 mm) deep-well socket
1. Loosen mounting bolt on top side of machine
deck while holding adjusting nut on underside
of deck. NOTE: The mounting bolt must be
loosened before adjustment can be made.
2. Rotate adjusting nut counter clockwise with
socket to apply tension to belt.
3. While holding the tension on the adjusting
nut, tighten the mounting bolt on the top of the
deck.
4. Check belt tension by pinching belt together.
Belt should depress only ½” (12 mm).
To Order Parts Call 1-888-702-5326 - https://monsterfloorequipmentparts.com