background image

_______________________________________________________________________________________________________________________________ 

European Safety Systems Ltd.

   Impress House, Mansell Road, Acton, London W3 7QH 

   Tel: +44 (0)208 743 8880 

 [email protected]    

www.e-2s.com   

 Fax: +44 (0)208 740 4200 

Document No. D202-00-201-IS_Issue_1         07-05-2019                         Sheet 1 of 8

 

INSTRUCTION MANUAL (ATEX / IECEx / CLASS DIV / UL38) 

GNExCP7-PT-S & GNExCP7-PT-D CALL POINTS 

For use in Flammable Gas Atmospheres 

1) Warnings

USE COVER BOLTS CLASS A4-70

DO NOT OPEN WHEN AN EXPLOSIVE

ATMOSPHERE IS PRESENT

POTENTIAL ELECTROSTATIC CHARGING

HAZARD

 

– SEE INSTRUCTIONS

FOR INDOOR USE

TO REDUCE THE RISK OF IGNITION OF
HAZARDOUS ATMOSPHERES, CONDUIT RUNS

MUST HAVE A SEALING FITTING CONNECTED

WITHIN 18 INCHES OF CONDUIT

AVERTISSEMENT:

UTILISER COUVRIR BOULONS CLASSE A4-70

NE PAS OUVRIR UN PRESENCE

D'ATMOSPHERE EXPLOSIVE

DANGER POTENTIEL CHARGE

ÉLECTROSTATIQUE -  VOIR LES INSTRUCTIONS

POUR USAGE INTÉRIEUR

POUR RÉDUIRE LE RISQUE D'INFLAMMATION

DES ATMOSPHÈRES DANGEREUSES, LES

CONDUITES DE CONDUIT DOIVENT AVOIR UN

RACCORD D'ÉTANCHÉITÉ RACCORDÉ À MOINS

DE 18 POUCES DE L'ENFERMEMENT

2) Rating & Marking Information

The GNExCP7PT callpoints meet the following standards for 
Fire Alarm System Use:  

UL 38 8th Edition 10/4/2013 Manual Signaling Boxes for Fire 

Alarm Systems 

ULC-S528 3rd Edition 2014-10 Manual Stations For Fire 
Alarm Systems, Including Accessories 

2.1 NEC & CEC Class / Division Ratings for US / Canada 

The GNExCP7PT callpoints comply with the following 
standards:  

UL 60079-0:2017 (Ed 6): Explosive Atmospheres - Part 0: 

Equipment - General requirements  
UL 60079-1:2015 (Ed7): Explosive Atmospheres - Part 1: 

Equipment protection by flameproof enclosures “d” 

UL 60079-31:2012 (Ed 2): Explosive Atmospheres - Part 31: 

Equipment dust ignition protection by enclosure "t" 

The Callpoints are rated as follows: 

Class I Div 2 Group ABCD T5 Ta -55°C to +70°C 
Class I Div 2 Group ABCD T6 Ta -55°C to +60°C 

Class II Div 2 Group FG T4 Ta -55°C to +70°C  

Class III Div 1 & 2 Ta -55°C to +70°C 

Installation must be carried out in compliance with the 

National Electric Code / Canadian Electric Code  

2.2 NEC Class / Zone ratings US 

The Callpoints are rated as follows: 

Class I Zone 1 AEx db IIC T5 Gb (Ta -55°C to +70°C) 

Class I Zone 1 AEx db IIC T6 Gb (Ta -55°C to +60°C) 
Zone 21 AEx tb IIIC T135°C Db (Ta -55°C to +70°C) 

Installation must be carried out in compliance with the 

National Electric Code. 

 

2.3 CEC Class / Zone ratings Canada 

The GNExCP7PT callpoints comply with the following 
standards:  

CSA C22.2 NO. 60079-0:2015 (Ed 3) Explosive Atmospheres 

– Part 0: Equipment – General requirements

CSA C22.2 NO. 60079-1:2016 (Ed 3): Explosive

Atmospheres – Part 1: Equipment protection by flameproof
enclosures “d”

CSA C22.2 NO. 60079-31:2015 (Ed 2): Explosive

Atmospheres – Part 31: Equipment dust ignition protection by

enclosure “t”

The Callpoints are rated as follows: 

Class I Zone 1 Ex db IIC T5 Gb X (Ta -55°C to +70°C) 

Class I Zone 1 Ex db IIC T6 Gb X (Ta -55°C to +60°C) 
Zone 21 Ex tb IIIC T135°C Db (Ta -55°C to +70°C)

 

Installation must be carried out in compliance with the 

Canadian Electric Code. 

 

Содержание GNExCP7-PT-S









Отзывы: