background image

INSTRUCTION MANUAL 

D1xB2X05-S, D1xB2X10-S, D1xB2X15-S 

Xenon Beacons 

 SIL2 

For use in Hazardous Locations 

 

E2S Warning Signals

      Impress House, Mansell Road, Acton, London W3 7QH

 

www.e2s.com

 

Tel: +44 (0)208 743 8880

 

Document No. D191-00-621-IS

 

Issue 1

 

27-10-22

 

 

Sheet 1 of 15

 

  

 
 

 

D1xB2X05-S 
D1xB2X10-S 
D1xB2X15-S 

 

 
 

1)  Warnings 

 

 DO NOT OPEN WHEN AN EXPLOSIVE 

ATMOSPHERE IS PRESENT 

 DO NOT OPEN WHEN ENERGISED 

 POTENTIAL ELECTROSTATIC CHARGING 

HAZARD - CLEAN ONLY WITH A DAMP 
CLOTH 

 HIGH VOLTAGE SHOCK HAZARD. WAIT 5 

MINUTES AFTER REMOVING POWER 
BEFORE OPENING THE ENCLOSURE 

 DO NOT PAINT 

 TO REDUCE THE RISK OF IGNITION OF 

HAZARDOUS ATMOSPHERES, THE FIRST 
CONDUIT RUN MUST HAVE A SEALING 
FITTING CONNECTED WITHIN 18 INCHES 
OF ENCLOSE. SUBSEQUENT CONDUIT 
RUNS MUST HAVE A SEALING FITTING 
CONNECTED AS CLOSE AS PRACTICAL TO 
THE WALL OF THE ENCLOSURE, BUT IN 
NO CASE MORE THAN THE SIZE OF THE 
CONDUIT OR 50MM, WHICHEVER IS THE 
LESSER. 

 TO PREVENT IGNITION OF GROUP A, B, C 

AND D ATMOSPHERES - SEE       
INSTRUCTION FOR CHEMICAL 
COMPATIBILITY 

 

Avertissement: 
 

 NE PAS OUVRIR UN PRESENCE 

D’ATMOSPHERE EXPLOSIVE

 

 NE PAS OUVRIR ENERGIE 

 DANGER POTENTIEL CHARGE 

ÉLECTROSTATIQUE - NETTOYER 
UNIQUEMENT AVEC UN CHIFFON HUMIDE 

 HAUT TENSION, RISK DE CHOC. 

ATTENDEZ 5 MINUTES APRES AVOIR 

DEBRANCHE L’ALIMENTATION AVANT 

D’OUVRIR LA BOITIER

 

 NE PAS PEINTURER 

 POUR RÉDUIRE LE RISQUE 

D'INFLAMMATION DES ATMOSPHÈRES 
DANGEREUSES, LE PREMIER CONDUIT DE 
CONDUIT DOIVENT AVOIR UN RACCORD 
D'ÉTANCHÉITÉ RACCORDÉ À MOINS DE 18 

POUCES DE L'ENFERMEMENT. POUR 
SUBSÉQUENT LES

 

CONDUITES DE 

CONDUIT LA DISTANCE ENTRE LA 
SURFACE DE LA MASSE DE REMPLISSAGE 

AU PLUS PRÈS DE L’ENVELOPPE DOIT 

ÊTRE AUSSI PETITE QUE CE QUI EST 
RÉALISABLE MAIS EN AUCUN CAS 
SUPÉRIEURE À LA PLUS PETITE DES 
DIMENSIONS CORRESPONDANT À LA 
TAILLE DU CONDUIT OU À 50 MM. 

 POUR PRÉVENIR L'INFLAMMATION DES 

ATMOSPHÈRES DES GROUPES A, B, C ET 
D-VOIR L'INSTRUCTION POUR LA 
COMPATIBILITÉ CHIMIQUE 

 

2)  Rating & Marking Information 

 

2.1 Fire Alarm Ratings 

 
The Following models are certified as visual alarm devices for 
fire  alarm  use 

  private  mode  only  when  used  with  Clear  or 

Red lens covers: 
 
D1xB2X05DC024 / D1xB2X10DC024 / D1xB2X15DC024 
 
On-axis light output per UL1638: 
 

Model 
D1xB2

 

Light Intensity in cd

 

Clear Lens

 

Red Lens 

X05DC024-S - 1Hz 

20.44

 

5.89

 

X05DC024-S - 1.33Hz 

14.47

 

4.17

 

X05DC024-S - 1.5Hz 

11.1

 

2.13

 

X10DC024-S - 1Hz 

69.81

 

23.66

 

X10DC024-S - 1.33Hz 

49.42

 

16.75

 

X10DC024-S - 1.5Hz 

35.71

 

8.57

 

X15DC024-S - 1Hz 

98.61

 

31.83

 

X15DC024-S - 1.33Hz 

69.81

 

22.53

 

X15DC024-S - 1.5Hz 

50.44

 

11.53

 

 

Содержание D1xB2X05 Series



















Отзывы: