manualshive.com logo in svg

E-Z-GO 4-STROKE AIR-COOLED GASOLINE ENGINE, Руководство по ремонту магазина, Страница: 94 / 100

Поделиться
Скачать
E-Z-GO 4-STROKE AIR-COOLED GASOLINE ENGINE Скачать руководство пользователя страница 94

Page G-12

LIMITED WARRANTY - CALIFORNIA (2001)

Kawasaki Engine Shop Rebuild Manual

part which is scheduled for replacement as required maintenance shall be warranted for the pe-

riod of time up to the first scheduled replacement point for that part.

3. DIAGNOSIS

You shall not be charged for diagnostic labor which leads to the determination that a warranted 

part is defective, if the diagnostic work is performed at an authorized dealer, distributor or service 

provider.

4. CONSEQUENTIAL DAMAGES

If a warranted part failed causing damages to other engine components, consult a service provid-

er.

D. WHAT IS NOT COVERED

1. This limited warranty does not cover any part which malfunctions, fails or is damaged due to failure to 

follow the maintenance and operating instructions set forth in the 2001 and later Owner’s Manual in-

cluding:

(1) improper or inadequate scheduled engine inspection and maintenance
(2) improper or inadequate maintenance of any warranted parts
(3) improper installation, adjustment or repair of the engine or of any warranted part unless per-

formed by an authorized dealer

(4) failure to follow recommendations on fuel use contained in the 2001 and later Owner’s Manual
(5) repairs performed outside of the authorized warranty service facilities
(6) use of parts which are not authorized by FUJI.

2. Add-on or modified parts

This warranty does not cover any part which malfunctions, fails or is damaged due to alterations 

by changing, adding to or removing parts from the engine.

3. Expenses incurred by processing warranty claims

FUJI, any authorized dealer, distributors and service providers shall not be liable for any loss of 

use of the engine, for any alternative usage, for any damage to goods, loss of time or inconve-

nience.

E. HOW TO FILE A CLAIM

All repairs qualifying under this Limited Warranty must be performed by a dealer who sold you the engine 

or distributors or service providers authorized by Textron Golf, Turf & Specialty Products. In the event that 

any emission-related part is found to be defective during the warranty period, you should notify Textron 

Golf, Turf & Specialty Products Warranty Department at 1-800-241-5855 and

 

you will be given the appro-

priate warranty service facilities where the warranty repair is performed.

F. WHERE TO GET WARRANTY SERVICE

It is recommended that warranty service be performed by the authorized dealer who sold you the engine, 

although warranty service will be performed by any authorized dealer, distributor and service provider any-

where in the United States. When warranty repair is needed, the engine must be brought to an authorized 

dealer, distributorship or service provider’s place of business during normal business hours. In all cases, 

a reasonable time, not to exceed 30 days, must be allowed for the warranty repair to be completed after 

the engine is received by the authorized dealer, distributor or service station.

G. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Only warranted engine replacement parts approved by FUJI should be used in the performance of any war-

ranty maintenance or repairs on emission-related parts. If other than authorized parts are used for mainte-

nance, replacement or repair of components affecting emission control, you should assure yourself that 

such parts are warranted by their manufacturer to be equivalent to authorized parts in performance and 

durability. FUJI, however, assumes no liability under this warranty with respect to parts other than autho-

rized parts. The use of non-authorized replacement parts does not invalidate the warranty on other com-

ponents unless the non-authorized parts cause damage to warranted parts.

H. PARTS COVERED UNDER THE CALIFORNIA EMISSIONS WARRANTY

(1) Fuel Metering System

(i) Carburetor and internal parts (and/or pressure regulator or fuel injection system)

(ii) Air/fuel ration feedback and control system, if applicable

(iii) Cold start enrichment system, if applicable

(iv) Regulator assembly (gaseous fuel, if applicable)

(2) Air Induction System

(i) Intake Manifold, if applicable

(ii) Air Filter

(3) Ignition System

(i) Spark Plugs

(ii) Magneto or Electronic Ignition System

Содержание 4-STROKE AIR-COOLED GASOLINE ENGINE





































































































Отзывы:

Нет отзывов