E-Seek 200 Скачать руководство пользователя страница 12

Страница: 12 / 16

- 12 -

Magnetic Track Setup

Description:

To setup each magnetic stripe track parameters, changes will be effective

after scanner ACK response.

Scanner Response:

ACK / NAK

Description

Field

Values allowed

Magnetic Track 1, 2, 3

Enable *

MAG1EN=1

Disable

MAG1EN=0

Enable *

MAG2EN=1

Disable

MAG2EN=0

Enable *

MAG3EN=1

Disable

MAG3EN=0

Table 2.9

LRC (Longitudinal Redundancy Check Character) Setup

Description:

To setup track data with LRC (Check Character) to the host after

decoding. Changes will be effective after scanner ACK response. This command affects
all enabled tracks.

Scanner Response:

ACK / NAK

Description

Field

Values allowed

LRC Character

Enable

MAGLRC=1

Disable *

MAGLRC=0

Table 2.10

Magnetic Raw Data Setup

Description:

To setup raw data output to the host. Each 8-bit raw data is encoded into

two ASCII characters.

Example:

0000 0110 1011 0000

---- ---- ---- ----

"0" "6" "B" "0"

4 leading zeros + data + 4 trailing zeros

Hex representation: "06B0"

** The number of leading and trailing zeros may vary from time to time, depending on
the characteristic of the F2F chip.
Changes will be effective after scanner ACK response. This command affects all
enabled tracks.

Scanner Response:

ACK / NAK

Description

Field

Values allowed

Raw Data Output

Enable

MAGRAW=1

Disable *

MAGRAW=0

Table 2.11

Содержание 200

















Результаты поиска

Содержание 200

Отзывы:

Бренды по названию

Популярные бренды

E-Seek 200, Руководство по программированию

Результаты поиска

Содержание 200

Отзывы:

Бренды по названию

Популярные бренды