• When sound alarm is on, will display.
• When vibration is on, will display.
• When both sound and vibration
are on, will display.
Version 160720
How to Set the Time and Date
How to Set up to 8 Daily Alarms
How to Set the Alarm to Beep and/or Vibration
How to Set the Stopwatch
Four Display Modes
How to Set the Countdown Interval Timer
1)
Select the Time
Mode by pressing
MODE
repeatedly if not already shown. Press and hold
LIGHT
for five (5) seconds. This will cause the
seconds to begin flashing.
2)
Press
MODE
and the minutes will flash. Press
ST/STP
to advance the minutes. Press
MODE
to
record the minutes. The hour will now flash.
3)
Please note the “AM” or “PM”
Indicator to the left of the hour digits.
Press
ST/SP
to advance the hour,
then press
MODE
to record the hour.
4)
The date will flash. Press
ST/SP
to advance the date, then press
MODE
to record the date.
5)
The month will flash. Press
ST/SP
to advance
the month, then press
MODE
to record the month.
6)
The year will flash. Press
ST/SP
to advance the
year, then press
MODE
to record the year.
7)
Press
LIGHT
to confirm the Time and Date
Settings and return to Time Mode.
AM
1)
Select the Alarm
Mode (AL) by pressing
MODE
repeatedly if not already shown.
2)
Press
ST/STP
once to turn on the beeping
alarm, twice to turn on the vibration, or three times
to turn on both alarm and vibration.
To temporarily display the Date in Time Mode,
Press
RESET
.
These symbols can be found above
the AM/PM indicator on the left
side of the display.
1)
Select the Alarm
Mode (AL) by pressing
MODE
repeatedly if not already shown. Alarms are shown in
the top right-hand corner, numbered A1-A8.
2)
To set Alarm 1, press and hold
LIGHT
until hour
flashes. Press
ST/STP
to advance the hour, then press
MODE
to record the hour.
3)
The minutes will flash. Press
ST/STP
to advance
the minutes, then press
MODE
to record the minutes.
4)
Press
LIGHT
to confirm the time entered.
etc. will appear above the time to show that the
alarm has been set.
5)
Press
RESET
to move between alarms (A1-A8).
Repeat steps 1-4 for each alarm you want to set.
6)
When you are finished setting alarms press
MODE
repeatedly until you reach Time Mode.
1)
Select the Stopwatch
Mode (ST) by pressing
MODE
repeatedly if not already shown. “ST” will appear on
the top of the display.
2)
Press ST/STP to start/stop the stopwatch.
3)
Press RESET to return to 0.
The Countdown Timer works within a set time-
frame every day - for example, 8:00AM to 9:00PM.
Within these hours the watch will alarm at set
intervals- for example, every hour, or every 2 hours.
Set in hours and minutes (Minimum Interval 15 min.)
To set the Time Frame/ Time Interval:
1)
Select the Countdown Timer Mode (TR) by pressing
MODE
repeatedly if it is not already shown.
2)
Press and hold
LIGHT
until the starting hour flashes.
This is when the countdown timer will start every day.
Press
ST/STP
to advance to this hour.
3)
Press
MODE
and the ending hour will flash. This is
when the countdown timer will stop every day. This
hour must be later than the starting hour. Press
ST/STP
to advance to this hour.
ST/STP
turns the Countdown Interval Timer on and
off.
The timer must be manually restarted every day.
Timer can only be started if within the set time frame.
Make sure to set the Alarm to Beep and/or Vibration.
Flip through the display modes by pressing the MODE button repeatedly.
Time Mode
Alarm Mode
Countdown
Timer Mode
Stopwatch Mode
“AL”
“ST”
“TR”
This section explains how to set Beep/Vibration/Both
for ALL Alarms, including the Countdown Timer.
Alarms auto-reset at midnight and repeat automatically
again at the same time the next day.
Next Set the Time Interval
(Ex: 30 min, 1 hr, 3hrs, etc.)
:
4)
Press
MODE
and the hour flash. Press
ST/STP
to
advance the hour, then press
MODE
to record the hour.
5)
The minutes will flash. Press
ST/STP
to advance the
minutes, then press
MODE
to record the minutes.
6)
Press
LIGHT
to confirm the timer settings.
