background image

32

33

32

33

Replacement Parts List

EFLB1101S . . . . . . . . . . 110mAh 1S 3.7V Li-Po: BMCX

EFLC1003 . . . . . . . . . . . 1S 3.7V Li-Po Charger, 0.3A: BMCX

EFLH1064 . . . . . . . . . . . MLP4DSM 4-Channel Transmitter, 2.4GHz: BMCX

EFLH1065 . . . . . . . . . . . 5-in-1 Control Unit, Rx/Servos/ESCs/Mixer/Gyro: BMCX

EFLH1066 . . . . . . . . . . . Replacement Servo Mechanics (2): BMCX

EFLH2209 . . . . . . . . . . . Motor w/Pinion, Left: BMCX

EFLH2210 . . . . . . . . . . . Motor w/Pinion, Right: BMCX

EFLH2211 . . . . . . . . . . . Inner Shaft Main Gear: BMCX

EFLH2212 . . . . . . . . . . . Inner Shaft w/Head/Hub: BMCX

EFLH2213 . . . . . . . . . . . Outer Shaft, Main Gear and Bushing Holder Set: BMCX

EFLH2214 . . . . . . . . . . . Outer Shaft Retaining Collar Set: BMCX

EFLH2215 . . . . . . . . . . . Outer Shaft Bearing, 3x6x2mm (2): BMCX

EFLH2216 . . . . . . . . . . . Swashplate Set: BMCX

EFLH2217 . . . . . . . . . . . Lower Rotor Head & Linkage Set: BMCX

EFLH2218 . . . . . . . . . . . Servo Pushrod Set: BMCX

EFLH2219 . . . . . . . . . . . Stabilizer Flybar Set: BMCX

EFLH2220 . . . . . . . . . . . Lower Main Blade Set (1 pair): BMCX

EFLH2221 . . . . . . . . . . . Upper Main Blade Set (1 pair): BMCX

EFLH2322 . . . . . . . . . . . S300 Landing Skid and Battery Mount: BMCX  

EFLH2323 . . . . . . . . . . . S300 Tail Boom and Angle Adapter: BMCX  

EFLH2224 . . . . . . . . . . . Main Frame Set: BMCX

EFLH2225 . . . . . . . . . . . Hardware Set: BMCX

EFLH2226 . . . . . . . . . . . Body/Canopy Mounting O-Ring (8): BMCX

EFLH2327 . . . . . . . . . . . S300 Body/Canopy, w/ Decals: BMCX

EFLH2328 . . . . . . . . . . . S300 Tail Rotor and Fin Set: BMCX 

EFLH2324 . . . . . . . . . . . S300 Tail Boom Accent Set: BMCX  

Option Parts List

EFLH2216GL . . . . . . . . . Swashplate Set, Glow in the Dark: BMCX

EFLH2220GL . . . . . . . . . Lower Main Blade Set, Glow in the Dark (1 pr): BMCX

EFLH2220W  . . . . . . . . . Lower Main Blade Set, White with Decals (1pr): BMCX

EFLH2221GL . . . . . . . . . Upper Main Blade Set, Glow in the Dark (1 pr): BMCX

EFLH2221W  . . . . . . . . . Upper Main Blade Set, White with Decals (1pr): BMCX

EFLH2222GL . . . . . . . . . Landing Skid & Batt Mnt Set, Glow in the Dark: BMCX

EFLH2224GL . . . . . . . . . Main Frame Set, Glow in the Dark: BMCX

EFLH2227W  . . . . . . . . . Body/Canopy, White without Decals: BMCX

EFLH2228GL . . . . . . . . . Vertical Fin, Glow in the Dark without Decals: BMCX

EFLH2228W  . . . . . . . . . Vertical Fin, White without Decals: BMCX

EFLH2230 . . . . . . . . . . . Decal Sheet, Blue/Silver Graphics: BMCX

EFLC1004 . . . . . . . . . . . 4-port Charger

EFLC1005 . . . . . . . . . . . 6V Power Supply (For 4-port Charger)

Warranty Period

Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) 

will be free from defects in materials and workmanship at the date of purchase by 

the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser (“Purchaser”) and is not 

transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS 

THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those 

Products purchased from an authorized Horizon dealer. Third party transactions 

are not covered by this warranty. Proof of purchase is required for warranty claims. 

Further, Horizon reserves the right to change or modify this warranty without notice 

and disclaims all other warranties, express or implied.

(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS 

OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOWLEDGES THAT 

THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE 

REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon 

will, at its option, (i) repair or (ii) replace, any Product determined by Horizon to be 

defective. In the event of a defect, these are the Purchaser’s exclusive remedies. 

Horizon reserves the right to inspect any and all equipment involved in a warranty 

claim. Repair or replacement decisions are at the sole discretion of Horizon. This 

warranty does not cover cosmetic damage or damage due to acts of God, accident, 

misuse, abuse, negligence, commercial use, or modification of or to any part of 

the Product. This warranty does not cover damage due to improper installation, 

operation, maintenance, or attempted repair by anyone other than Horizon. Return of 

any goods by Purchaser must be approved by Horizon before shipment.

Damage Limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL 

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY 

CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT, 

WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability 

of Horizon exceed the individual price of the Product on which liability is asserted. As 

Horizon has no control over use, setup, final assembly, modification or misuse, no 

liability shall be assumed nor accepted for any resulting damage or injury. By the act 

of use, setup or assembly, the user accepts all resulting liability.

If you as the Purchaser or user are not prepared to accept the liability associated 

with the use of this Product, you are advised to return this Product immediately in 

new and unused condition to the place of purchase.

Содержание Blade MCX S300





















Отзывы: