background image

27

E-flite Beechcraft 480 Staggerwing 480 ARF Assembly Manual

LIMITATION OF LIABILITy

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, 

INDIRECT, INCIDENTAL OR CONSEQUENTIAL 

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR 

COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF 

WHETHER SUCH CLAIM IS BASED IN CONTRACT, 

WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY 

OR ANY OTHER THEORY OF LIABILITY, EVEN IF 

HORIZON HAS BEEN ADVISED OF THE POSSIBILITY 

OF SUCH DAMAGES. Further, in no event shall the 

liability of Horizon exceed the individual price of the 

Product on which liability is asserted. As Horizon 

has no control over use, setup, final assembly, 

modification or misuse, no liability shall be assumed 

nor accepted for any resulting damage or injury. By 

the act of use, setup or assembly, the user accepts all 

resulting liability. If you as the purchaser or user are 

not prepared to accept the liability associated with the 

use of the Product, purchaser is advised to return the 

Product immediately in new and unused condition to 

the place of purchase.

LAW

These terms are governed by Illinois law (without 

regard to conflict of law principals).  This warranty 

gives you specific legal rights, and you may also have 

other rights which vary from state to state.  Horizon 

reserves the right to change or modify this warranty at 

any time without notice.

Warranty Services

QUESTIONS, ASSISTANCE, AND SERVICES

Your local hobby store and/or place of purchase 

cannot provide warranty support or service. Once 

assembly, setup or use of the Product has been started, 

you must contact Horizon directly. This will enable 

Horizon to better answer your questions and service 

you in the event that you may need any assistance. 

For questions or assistance, please direct your 

email to [email protected], or call 

877.504.0233 toll free to speak to a Product Support 

representative. You may also find information on our 

website at www.horizonhobby.com.

INSpECTION OR SERVICES

If this Product needs to be inspected or serviced, please 

use the Horizon Online Service Request submission 

process found on our website or call Horizon to obtain 

a Return Merchandise Authorization (RMA) number. 

Pack the Product securely using a shipping carton. 

Please note that original boxes may be included, but 

are not designed to withstand the rigors of shipping 

without additional protection. Ship via a carrier that 

provides tracking and insurance for lost or damaged 

parcels, as Horizon is not responsible for merchandise 

until it arrives and is accepted at our facility. An 

Online Service Request is available at http://www.

horizonhobby.com under the Support tab. If you 

do not have internet access, please contact Horizon 

Product Support to obtain a RMA number along with 

instructions for submitting your product for service. 

When calling Horizon, you will be asked to provide 

your complete name, street address, email address 

and phone number where you can be reached during 

business hours. When sending product into Horizon, 

please include your RMA number, a list of the included 

items, and a brief summary of the problem.  A copy 

of your original sales receipt must be included for 

warranty consideration. Be sure your name, address, 

and RMA number are clearly written on the outside of 

the shipping carton.

Notice: Do not ship Lipo batteries to horizon. If you 

have any issue with a Lipo battery, please contact 

the appropriate horizon product Support office.

WARRANTy REQUIREMENTS 

For Warranty consideration, you must include your 

original sales receipt verifying the proof-of-purchase 

date. 

Provided warranty conditions have been met, 

your Product will be serviced or replaced free of 

charge. Service or replacement decisions are at the 

sole discretion of Horizon.

NON-WARRANTy SERVICE

Should your service not be covered by warranty 

service will be completed and payment will be 

required without notification or estimate of the 

expense unless the expense exceeds 50% of the 

retail purchase cost. 

By submitting the item for service 

you are agreeing to payment of the service without 

notification. Service estimates are available upon 

request. You must include this request with your item 

submitted for service. Non-warranty service estimates 

will be billed a minimum of ½ hour of labor. In 

addition you will be billed for return freight. Horizon 

accepts money orders and cashiers checks, as well as 

Visa, MasterCard, American Express, and Discover 

cards. By submitting any item to Horizon for service, 

you are agreeing to Horizon’s Terms and Conditions 

found on our website http://www.horizonhobby.com/

Service/Request/. 

UNITED STATES

(Electronics and engines)

Horizon Service Center

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

Online Repair Request visit:

www.horizonhobby.com/service

(All other products)

Horizon Product Support

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

Содержание Beechcraft Staggerwing 480 ARF

































Отзывы: