E.F. Johnson Company ATLAS 4500 Скачать руководство пользователя страница 13

Страница: 13 / 54

ATLAS 4500 Multimode Station Technical Manual

May 2017

1-3

Regulatory Information

Section 1 - Introduction

1.2.3 Warnings and Cautions

Observe all warnings and cautions when working on or around this equipment.

1.3 Regulatory Information

This section contains the following statements:

• FCC RF Warning Statement

• FCC Part 15.19 Warning Statement

• FCC Part 15.21 Warning Statement

• FCC Part 15.105(b) Warning Statement

• IC RSS-GEN, Sec 8.4 Warning Statement

• IC RSS-GEN, Sec 8.3 Warning Statement

• IC RSS-102, Sec 2.6 Warning Statements

1.3.1 FCC RF Warning Statement

WARNING

• Radio frequency radiation. A radio frequency (rf) radiation hazard exists in this equipment. To

avoid rf injury, do not touch the antenna when the transmitter is in use. Do not operate transmitter

with antenna disconnected.

• Thermal or RF burns. Do not attempt internal servicing while transmitting. Thermal or RF burns

may result from touching certain components within the power amplifier module while transmitting

or operating the transmitter.

• Shock Hazard. To minimize any possible shock hazard from an external power supply or lightning

strike, the chassis of the equipment cabinet must to be connected to an electrical safety earth

connection.

• Do not operate in an explosive atmosphere. Do not operate this equipment in the presence of

flammable gases or fumes. operation of any electrical equipment in such an environment

constitutes a definite safety hazard.

• Do not substitute parts or modify the equipment. Due to the danger of introducing additional

hazards, do not install substitute or lower voltage parts to the equipment. Return to your authorized

distributor.

• Beryllium and beryllia. Most rf power transistors and some rf power hybrids contain beryllium

oxide. Refer to the appropriate safety data sheet and/or consult your local authority for correct

disposal thereof.

CAUTION

Electrostatic Discharge Sensitive Devices (ESDS Devices). Observe the appropriate

precautions and procedures when working on, or in the vicinity of, this equipment to avoid

personal injury and/or damage to the equipment

CAUTION

This repeater emits radio frequency (RF) energy when transmitting. Make sure to observe all RF

energy exposure standards when installing, testing, repairing, and operating this radio equipment.

Содержание ATLAS 4500























































Результаты поиска

Содержание ATLAS 4500

Отзывы:

Похожие инструкции для ATLAS 4500

Бренды по названию

Популярные бренды

E.F. Johnson Company ATLAS 4500, Техническое руководство

Результаты поиска

Содержание ATLAS 4500

Отзывы:

Похожие инструкции для ATLAS 4500

Бренды по названию

Популярные бренды