E.F. Johnson Company 53SL ES Series Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 190

background image

53SL ES Series Mobile Radio Operating Manual April 2009

6-23

Keypad Programming

Section 6 - Conventional Mode Features

6.14

Keypad Programming

Since keypad programming is permitted by Federal Government users only, only Federal
models of this transceiver can be programmed with this feature. It is then available only if
it has been enabled by factory programming and a conventional mode option switch is
programmed for the “Keypad Programming” function.

Note

The Keypad programming feature is available to Federal Government users only. Users
regulated by the Federal Communications Commission (FCC) are not allowed to have
this feature. This feature must be factory enabled to be selected

Keypad programming is selected by pressing the PROG option switch or by selecting the
option from the menu (password entry is not required). The keypad programming mode is
indicated by “CHNG ZONE” and a triangle in the display as follows:

Keypad programming allows conventional channel parameters such as the transmit and
receive frequency, Call Guard squelch code, and encryption key to be changed. In
addition, several conventional mode timers can be changed. It cannot be used to
reprogram disabled channels or any P25 Trunked, SMARTNET, or SmartZone
information.

6.14.1 Menu Structure

A menu system is used to select parameters in the keypad programming mode. To enter
the Menu Mode, press and hold the Select button until it beeps and enters the Menu Mode.
Rotate and press the Select switch to scroll through and select the available parameters.
The available parameters and the section in which each is described are as follows:

• CHNG ZONE (6.14.3)

• CHNG CHAN (6.14.4)

• SYS PARMS (6.14.5)

• CHAN PARMS (6.14.6)

«
...
101
102
103
104
105
...
»

Содержание 53SL ES Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 53SL ES Series

Бренд: MicRadar Страницы: 13

Бренд: Buck Rogers Страницы: 58

Бренд: Radio Shack Страницы: 16

Бренд: Cobra Marine Страницы: 33

Бренд: Ocean Digital Страницы: 2

Бренд: Goodmans Страницы: 24

Бренд: Eurochron Страницы: 8

Бренд: Hama Страницы: 70

Бренд: Sangean Страницы: 1

Бренд: Sangean Страницы: 1

Бренд: GE Страницы: 31

Бренд: GE Страницы: 8

Бренд: Tait Страницы: 120

Бренд: Vertex Standard Страницы: 63

Бренд: Motorola Страницы: 87

Бренд: Motorola Страницы: 60

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды