E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 142

background image

5300 ES Series Mobile Radio Operating Manual

10-15

Secure Communication (Encryption)

MODIFY KEY

0x13

MODIFY KEYSET ATTRIBUTES

0x14

MODIFY KEYSET ATTRIBUTES RESPONSE

0x15

NEGATIVE ACK

0x16

NO SERVICE

0x17

REKEY ACK

0x1D

REKEY

0x1E

WARM START

0x20

ZEROIZE

0x21

ZEROIZE RESPONSE

0x22

OTAR REGISTRATION

0x25

OTAR REGISTARTION RESPONSE

0x26

UNABLE TO DECRYPT

0x27

10.6.1 OTAR Option Switches

The following additional option switches can be programmed with the 5300 ES mobile
radio to control OTAR functions.

Change Keyset - Toggles the active keyset between Keyset 1 and Keyset 2. The new
active keyset is briefly displayed and then normal operation resumes. To change to the
other keyset, highlight it and press the <F2> key.

Clear/Secure Select - This enables and disables encryption regardless of whether
OTAR is used. Refer to Section 10.3 for more information.

Erase Keys - Erases all TEK and KEK keys contained in the radio.

Key Select - This allows a different key to be selected for the current channel or group
(conventional channels only). Refer to Section 10.2.4 for more information.

OTAR Rekey Request - Sends a message which tells the KMF that the radio is on the
air and requests rekeying. The following status messages are displayed which indicate
the progress of this function.

Rekeying - A radio-initiated rekeying session is in process.

No Ack - No response was received from the KMF in response to an Identify request
before time out occurred (approximately 30 seconds).

Ack Rcvd - An acknowledgement was received in response to an Identify request.

«
...
129
130
131
132
133
...
»

Содержание 5300 ES Series















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5300 ES Series

LUNCHBOX LB-100

Бренд: Sangean Страницы: 1

Бренд: K40 Страницы: 2

Бренд: Sangean Страницы: 13

Бренд: SBO Hearing Страницы: 4

Бренд: Blue-Links Страницы: 10

Бренд: Geoscanners AB Страницы: 38

Бренд: camry Страницы: 48

Бренд: Hamilton Beach Страницы: 10

Бренд: Sencor Страницы: 14

Бренд: auna Страницы: 18

Бренд: Grundig Страницы: 30

Бренд: Retekess Страницы: 14

Бренд: Porter-Cable Страницы: 24

Бренд: SOUNDMASTER Страницы: 46

NS-HD01 - Portable HD Radio

Бренд: Insignia Страницы: 2

Бренд: Grundig Страницы: 15

Бренд: DIGITECH Audio Страницы: 14

Бренд: NAVICOM Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды