INSTALLATION INSTRUCTIONS
E-WPD SERIES
Document
Date
Drawing/Page
DCR#
CI308X35R1
JAD
10-162
08/03/10
1. Read carefully before installing the fixture.
2. Make certain power is OFF before starting installation or
attempting any maintenance.
CAUTIONS
To ensure proper installation and service, the fixture should be
mounted with the lamp in a horizontal position. Do not recess. Also,
make sure fixture is weatherproof by sealing all gaps and holes with
waterproof silicone sealant.
MOUNTING
IMPORTANT:
Read carefully before installing the fixture.
SAVE THESE INSTRUCTIONS
WARNING:
Turn off power supply to avoid the risk of electrical shock. This
product must be wired in accordance with the National Electrical
Code and applicable local codes and ordinances. Proper grounding
is required to ensure personal safety. A qualified electrician should
do all work. Minimum 90°C supply conductors required.
1. Loosen 2 screws located on the side of the fixture housing and
open fixture housing.
2. (Only necessary for 70, 100 or 150W fixtures) Loosen 2 screws on
reflector and remove.
3. Remove the screws (or four screws for the 250 or 400W fixtures)
on the ballast cover and remove.
4. Locate and remove the desired conduit plug on the top or the side
(or the back for 250W or 400W fixtures) of the fixture housing.
5. Mount the fixture to the wall by drilling holes through the back of
the fixture housing and using the appropriate mounting hardware
for the surface (supplied by customer). When drilling holes, do not
drill within ¼" (6.4 mm) of the edge of the fixture. Also, use
caution when drilling near the ballast, making sure not to nick or
leave metal chips on the ballast windings.
6. Attach conduit and pull supply leads through the conduit plug.
7. All unused holes must be plugged. Apply waterproof silicone to all
mounting holes and conduit plugs to ensure a tight seal.
8. Complete the wiring to the power source and ground (refer to
wiring instructions), making sure to keep wires away from
the ballast.
9. Replace ballast cover and reflector, install lamp, close fixture
housing and tighten the screws.
DIRECT MOUNTING USING CONDUIT
NOTE: The 250W and 400W fixtures may not be mounted directly to
the J-box.
1. Loosen 2 screws located on the side of the fixture housing.
2. Loosen 2 screws on reflector and remove.
3. Remove the 2 screws on the ballast cover and remove.
4. Remove appropriate knock-outs in back of ballast housing to
match J-box hole pattern.
5. Remove the center hole knock-out, route supply wires through the
center hole and secure fixture to J-box.
NOTE: When mounting in wet locations with a J-box,
a J-box rated for Wet Locations should be used.
6. All unused holes must be plugged. Apply waterproof silicone to all
mounting holes, conduit plugs, and between the fixture and
mounting surface to ensure a tight seal.
7. Complete the wiring to the power source and ground (refer to
wiring instructions), making sure to keep wires away from the
ballast if wiring inside fixture.
8. Replace ballast cover and reflector, install lamp, close fixture
housing and tighten screws.
MOUNTING TO JUNCTION BOX
(70, 100 or 150W FIXTURES ONLY)
w w w. e - c o n o l i g h t . c o m
8 8 8 . 2 4 3 . 9 4 4 5
FA X : 2 6 2 . 5 0 4 . 5 4 0 9
14
/
4
1
”
11
/
2
1
”
9
/
16
1
”
18
/
8
1
”
17
/
4
1
”
9
/
4
1
”
70, 100 or 150W Fixture
250W or 400W Fixture