background image

Document:  

Date

Created By: 

 

ECO# 

LPN00674X0001A0  12-22-2019

TMT  

011320

INSTALLATION INSTRUCTIONS

PHOTOCELL OPTIONS 

www.e-conolight.com      |     888.243.9445     |     FAX: 262.504.5409

FIGURE  4

Knockout

FIGURE 4

FIGURE  5

Place insulation

betwen PC

and Housing

Place insulation

betwen PC

and Housing
U-Slot

Thread nut

FIGURE 5

1.  Refer to mounting diagrams, 

Figure 7

, for correct fixture series 

and drill a 11/16” (17mm) hole in location indicated. Make sure the 

photocell will fit properly before drilling.

2.  See photocontrol installation

WALLPACKS WITHOUT KNOCKOUTS

E-WFT05

Photocell

MOUNTING DIAGRAMS

Photocell

E-WFC

Mounting Box

Photocell

E-WRT

Mounting Box

Photocell

E-WLT

Mounting Box

Photocell

*E-WF1L / E-WF2L

Mounting Box

*See Note 2 in 

Photocontrol Installation Below

Fixture Housing

FIGURE 7

1.  Remove nut from photocell, leave o-ring.

NOTE 1:

 For 1000W (208-277V) fixtures remove o-ring from 

photocell and replace with flat gasket provided. Discard o-ring. See 

Figure 8.
NOTE 2:

 When installing photocontrol on E-WF1L and E-WF2L 

accessories, add additional supplied nut and o-ring as shown in 

Figure 9.

2.  Slide photocell through opening.

3. 

Thread nut on to threaded nipple of photocontrol and tighten to 
ensure waterproof seal.

4. 

Wire photocontrol according to 

Figure 10

 if wiring phase to neutral 

or 

Figure 11

 if wiring phase to phase. In all cases make sure the 

photocontrol voltage is rated for the supply voltage.

5.  Reinstall any parts removed during the installation of the 

photocontrol.

PHOTOCONTROL INSTALLATION

(Flat gasket in 1000W,

    208-277V fixtures)

FIGURE 8

Locating knockout on E-WFS Series:

1.  Loosen (2) Phillips screws on driver door. See 

Figure 6.

2.  Open driver door.

3. 

Photocontrol knockout is located on either right or left side of 
housing, depending on model. See 

Figure 6.

4.  Using a hammer and a punch, remove knockout from side wall of 

driver compartment.

5.  Pull black and white leads through center grommet on back wall of 

driver compartment so splices to photocontrol can be made inside 
driver compartment.

6.  See Photocontrol Installation section.
7.  Push black lead from photocontrol and white lead through holes 

in grommet and gasket on back wall of driver compartment to 

allow splices to be made to supply leads in junction box or surface 
mounting box.

FIGURE 6

Driver Door

Phillips Head Screws

Knockout Locations (Varies 

Dependent On Model)

Содержание e-acp Series










Отзывы: