E-Cells FAT Series Скачать руководство пользователя страница 16

Страница: 16 / 22

OPERATION OF THE LCD DISPLAY AND MOTOR POWER PAD.

ONLINE MANUAL: https://ecells.com/wp-content/uploads/2020/06/750C-

Specifications-2018-Bluetoothdisplay-manual.pdf

BASIC FUNCTIONS

Turn on the screen

Press '' Power button '' and hold for 3 seconds

Turn on Front Light

Press + and hold for 3 seconds

Increase the level of pedal assistance

Press "+" on power pad

Decrease the level of pedal assistance

Press "– "on power pad

To Activate Walking Mode

Press and hold - the engine will activate

and maintain a speed of approximately

3.75 mph until you release the - button

Reset trip counter to zero

Hold + and - simultaneously for 3 seconds

MOTOR POWER SWITCH: RED TOGEL SWITCH ON LEFT HANDLEBAR

When the togel switch is on "

FWD:FRONT WHEEL DRIVE

When the switch is at "

AWD: ALL WHEEL DRIVE

dual motor drive. This is the

best performance and recommended for max power and efficiency.(The motors and

batteries run cooler, thus increasing efficiency.)

When the switch is at "

RWD: REAR WHEEL DRIVE ONLY

Programming functions on APT 750-C Bluetooth Dashboard Display

The advanced programming instructions are available on VIDEO and PDF on E-Cells.com

IMPORTANT POINTS

For optimal use, please consider that important information.

Mechanical safety check :

Check the condition of your bike regularly. Make sure that nothing has become loose.

Make a visual inspection of the entire bicycle before each ride. Make sure the tires are

properly inflated (about 8-30 PSI for the Super Monarch AWD 1500 Crown models). Also

check your brakes.

First ride :

To test your new electric bike, choose a place away from cars, cyclists and other potential

dangers to safely familiarize yourself with the controls and features of the bike. Starting

is much easier and faster than with a regular bike. Be careful these bikes are very

powerful.

Damage to the chain :

It is important not to change the speed of your bike on the derailleur when you are on the

high power assist mode. You must first choose your speed on the mechanical derailleur

and then you can use the electric assist mode. Changing the gear mechanically while the

power assistance mode is high may cause serious damage to your bike chain.

Содержание FAT Series























Результаты поиска

Содержание FAT Series

Отзывы:

Похожие инструкции для FAT Series

Бренды по названию

Популярные бренды

E-Cells FAT Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FAT Series

Отзывы:

Похожие инструкции для FAT Series

Бренды по названию

Популярные бренды