background image

 

Safety instructions 

The device has left our premises in absolutely perfect condition. In 
order to maintain this condition and to ensure a safe operation, it is 
absolutely necessary for the user to follow the safety instructions 

and warning notes written in this user manual. 

 

Keep away from heaters and other heating sources! 

If the device has been exposed to drastic temperature fluctuation 
(e.g. after transportation), do not switch it on immediately. The 
arising condensation water might damage your device. Leave the 
device switched off until it has reached room temperature. 
Please note that damages caused by manual modifications on the 

device or unauthorized operation by unqualified persons are not 
subject to warrenty, 
Keep away children and amateurs from the device and batteries! 

Operation Determinations 

Batteries are hazardous waste which need to be disposed of 
appropriately. If the device is to be disposed, the batteries have to 
be removed first. 

Make sure that the poles are correct when inserting the batteries. 
Never let batteries lying around openly as there is the danger that 
these can be swallowed by children or domestic animals. 
Immediately consult a doctor when batteries are swallowed! 

Leaking or damaged batteries can cause irritations when getting 
into contact with the skin. In this case use appropriate protective 
gloves. 
Make sure that the batteries cannot be short-circuited, thrown into 

the fire and be charged. There is a danger of explosion. 
Never put any liquids on the device or close to it. Should any liquid 
enter the device nevertheless, disconnect from mains immediately 
and remove the batteries. Please let the device be checked by a 
qualified service technician before you operate it again. Any 

damages caused by liquids having entered the device are not 
subject to warranty! 
When choosing the installation-spot, please make sure that the 
device is not exposed to extreme heat, moisture or dust. There 

should not be any cables lying around. You endanger your own and 
the safety of others! 
Do not operate the device in extremely hot (more than 35° C) or 
extremely cold (less than 5° C) surroundings. Keep away from 

direct insulation (particularly in cars) and heaters. 
Operate the device only after having familiarized with its functions. 
Do not permit operation by persons not qualified for operating the 
device. Most damages are the result of unprofessional operation! 
If the device will not be used for a longer period of time, remove 

the batteries in order to avoid battery leakage. 

Содержание infinity

























Отзывы: