8
USING YOUR DYSON APPLIANCE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
RATING PLATE
•
Your serial number can be found on the rating plate which is located either
(a) on the main body of the machine behind the clear bin or (b) on the top of the
appliance above the switches, under the wand handle.
•
To access the rating plate after assembling the machine:
– Open the wand cap and pull the red tube up and away from the handle.
– Press in the black clip in the recess of the duct.
– Pull the wand handle up and off the appliance; use a constant, firm pressure.
ASSEMBLY
•
Lie the appliance on its back.
•
Attach the cleaner head by sliding it on to the connections on the lower front part
of the ball. Ensure the electrical plug on the cleaner head fits into the twin-block
connection on the body of the appliance, which is directly above the airway.
Push firmly: the cleaner head will click into place.
•
Stand the appliance up straight.
•
Note the serial number before attaching the wand handle, if applicable.
•
Attach the wand handle by sliding it on to the top of the appliance. The spring
clip in the handle will click into place.
•
Ensure the hose is straight. Press the red button on the hose. Slide the wand into
the hose.
•
Ensure the hose and wand sit in the recess of the handle. Slide the end of the
wand down into the handle to secure it.
•
Close the wand cap.
•
Slide the tool holder onto the side of the duct as shown.
•
Ensure the cyclone and clear bin unit is secured to the main body of the
appliance.
•
Attach the tools as shown. In use, the tools can be attached to either the hose
or the wand.
•
Wind the cable anti-clockwise around the cable hooks. Secure with the clip.
•
To watch a short online video visit:
AU: www.dyson.com.au/DC65gettingstarted
NZ: www.dyson.co.nz/DC65gettingstarted
OPERATION
•
Unwind the cable.
•
Plug the appliance into the mains electricity supply.
•
To switch ‘ON’ or ‘OFF’ press the power button, located as shown.
•
To use, recline the handle. The stabiliser stand will automatically lift up.
•
After use, return the appliance to the upright position, pushing it firmly into
place. The stabiliser wheels will automatically lower.
•
Then unplug the appliance, coil the cable safely and put the appliance away.
•
Switch ‘OFF’ the appliance, unplug and ensure it is upright before:
– Changing or using tools.
– Removing the hose or airway inspection parts.
•
Use the cyclone carry handle to carry the appliance.
ATTACHMENTS
•
To release the wand, open the wand cap and pull the red tube up and away from
the handle until it clicks into place.
•
Should you wish to use the hose without the wand, follow the above instruction
and press the red button to release the wand from the hose.
CARPETS OR HARD FLOORS
•
The brush bar will always default to ‘ON’ (spinning) each time you switch the
appliance ‘ON’ and recline it for cleaning.
•
The brush bar will not rotate when the appliance is upright.
•
To switch the brush bar ‘OFF’ (e.g. for hard floors):
– Switch the appliance ‘ON’.
– Recline the appliance.
– Press the brush bar ‘ON/OFF’ button – the brush bar will stop spinning.
•
The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar –
clearing obstructions’ on pages 4 and 5 of this Dyson Operating Manual.
•
Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
•
Some carpets may fuzz if a rotating brush bar is used when vacuuming.
If this happens, we recommend vacuuming in ‘hard floor' mode and
consulting with the flooring manufacturer.
•
The brush bar on the appliance may damage some carpet types. If you are
unsure, turn ‘OFF’ the brush bar.
LOOKING AFTER YOUR DYSON APPLIANCE
•
Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Customer Care Helpline.
•
Only use parts recommended by Dyson. If you do not this could invalidate
your Dyson guarantee.
•
Store the appliance indoors. Do not use or store it below 0°C. Ensure the
appliance is at room temperature before operating.
•
Clean the appliance only with a dry cloth. Do not use any lubricants,
cleaning agents, polishes or air fresheners on any part of the appliance.
•
If used in a garage, always wipe the base plate, ball and stabiliser wheels with
a dry cloth after vacuuming to clean off any sand, dirt, or pebbles that could
damage delicate floors.
•
Check the brush bar regularly and clear away any debris (such as hair).
Debris left on the brush bar may cause damage to flooring when vacuuming.
VACUUMING
CAUTION:
•
Do not use without the clear bin and filters in place.
•
Fine dust such as plaster dust or flour should only be vacuumed in very small
amounts.
•
Do not use the appliance to pick up sharp hard objects, small toys, pins,
paper clips, etc. They may damage the appliance.
•
When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimise any effect from this, do not put your hand or insert
any object into the clear bin unless you have first emptied it and rinsed it out
with cold water. See ‘Cleaning the clear bin’ section on page 8 of this Dyson
Operating Manual.
•
Powerful suction can cause the hose to ‘pull back’ – please take care.
•
Do not work with the appliance above you on the stairs.
•
Do not put the appliance on chairs, tables, etc.
•
Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
•
Do not leave the cleaner head in one place on delicate floors during use.
EMPTYING THE CLEAR BIN
•
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
•
Switch ‘OFF’ and unplug before emptying the clear bin.
•
To remove the cyclone and clear bin unit, press down on the red button at the
rear of the carrying handle on the cyclone.
•
To release the dirt, press all the way down on the red button at the rear of the
carrying handle on the cyclone.
•
To minimise dust/allergen contact when emptying:
– Encase the clear bin tightly in a plastic bag and empty.
– Remove the clear bin carefully.
– Seal the bag tightly, dispose as normal.
•
To refit the clear bin:
– Close the clear bin base so it clicks into place.
– Push the cyclone and clear bin unit into the main body of the appliance;
it will click into place.
– Ensure the cyclone and clear bin unit is secure.
CLEANING THE CLEAR BIN
•
Remove the cyclone and clear bin (instructions above).
•
To separate the cyclone unit from the clear bin press the red button to open
the clear bin base. This exposes a small silver button behind the red opening
mechanism. Press the silver button and separate the cyclone unit from the clear bin.
•
Clean the clear bin with cold water only.
•
Ensure the clear bin is completely dry before replacing.
•
Do not use detergents, polishes or air fresheners to clean the clear bin.
•
Do not put the clear bin in a dishwasher.
•
Do not immerse the whole cyclone unit in water or pour water into the cyclones.
•
Clean the cyclone shroud with a dry cloth or dry brush to remove lint and dust.
•
To refit the bin to the cyclone unit:
– Close the clear bin base so it clicks into place.
– Fit the cyclone shroud into the clear bin so that the silver button clicks
and engages.
– Push the cyclone and clear bin unit into the main body of the appliance;
it will click into place.
– Ensure the cyclone and clear bin unit is secure.
WASHING YOUR FILTERS
•
Your appliance has two washable filters, located as shown on pages 6 and 7
of this Dyson Operating Manual.
•
Check and wash the filters every 3 months according to instructions to
maintain performance.
•
Switch ‘OFF’ and unplug before checking or removing the filters.
•
The filters may require more frequent washing if vacuuming fine dust.
•
Wash with cold water only. Do not use detergents.
•
Do not put the filters in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
•
To remove filter A see the ‘Wash filters’ section on pages 6 and 7 of this Dyson
Operating Manual.
•
After washing lay filter A on its side and leave for at least 24 hours to dry
completely before refitting.
•
To remove filter B:
– Turn the central locking dial on the outer cover of the ball anti-clockwise until
the cover is released.
– Lift off the cover.
– Turn the filter one-quarter anti-clockwise to release.
•
Filter B should be rinsed and tapped out until the water runs clean, then tapped
out again to ensure all excess water is removed. Leave to dry completely for
24 hours.
•
It is normal for the filter in the ball to turn grey in colour.
•
To refit filter B:
– Refit the filter on to the ball.
– Secure the filter by turning it one-quarter turn clockwise.
•
When refitting the outer cover of the ball, keep turning the central locking dial
clockwise. When it starts to click it is locked.
•
To watch a short online video visit:
AU: www.dyson.com.au/DC65filterwash
NZ: www.dyson.co.nz/DC65filterwash
LOOKING FOR BLOCKAGES
•
Switch ‘OFF’ and unplug before looking for blockages. Failure to do so could
result in personal injury.
•
Beware of sharp objects when checking for blockages.
•
Refit all parts securely before using.
•
Clearing blockages is not covered by your Dyson guarantee.
CLEARING BLOCKAGES – THERMAL CUT-OUT
•
This appliance is fitted with an automatically resetting thermal cut-out.
•
Large items may block the tools or wand inlet. If any part becomes blocked the
appliance may overheat and automatically cut-out.
•
Switch ‘OFF’ and unplug. Leave to cool down for 1-2 hours before checking
filters or for blockages.
•
Clear any blockages before restarting.
•
Clearing blockages is not covered by your Dyson guarantee.
