background image

 

B4850 ESS Unit User Manual                                                                  

11 

 

 

Caution:

  

The buzzer sound alarm setting can be manually turned off on the background software, and the 
factory default is on. 

2.4.3  Temperature Protection 

Low/Over temperature protection in charging

 

When  battery’s  temperature  is  beyond  range  of 

-5

~+55

during  charging,  temperature 

protection is activated, device stops charging.

 

The protection is over when temperature back to rated working range. 

Low/Over temperature protection in discharging

 

When  battery’s  temperature  is  beyond  range  of 

-20

~+55

  during  discharging,  temperature 

protection is activated, device stops supplying power to the outside.

 

The protection is over when temperature back to rated working range..

 

2.4.4  Other Protection 

Short Circuit Protection

 

When the battery is activated from the shutdown state, if a short circuit occurs, the system starts 
short-circuit protection for 60 seconds. 

Self-Shutdown

 

When device connects no external loads and power supply and no external communication for 
over 72 hours, device will dormant standby automatically. 

 

Caution

 

 

Battery’s maximum discharging current should be more than load’s maximum working current

3  Installation and Configuration 

3.1  Ready for installation 
Safety Requirement 

This system can only be installed by personnel who have been trained in the power supply system 
and have sufficient knowledge of the power system.  
The safety regulations and local safety regulations listed below should always be followed during 
the installation.

 

 

All circuits connected to this power system with an external voltage of less than 48V 
must meet the SELV requirements defined in the IEC60950 standard. 

 

If operating within the power system cabinet, make sure the power system is not 
charged. Battery devices should also be switched off

.

 

 

Distribution cable wiring should be reasonable and has the protective measures to 
avoid touching these cables while operating power equipment. 

 

when installing the battery system, must wear the protective items below: 

The isolation gloves            Safety goggles 

               Safety shoes      

Figure3-1

 

Содержание B4850

























Отзывы: