DynAmp LKAT2 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 45

DynAmp LKAT2 Скачать руководство пользователя страница 5

Installation, Operation and Service Manual

LKAT

2

+24V

© 2018 DynAmp, LLC

Page v

046404 E

Hazard Warning!

Symbol
Identification:

General definitions of safety symbols used on equipment and manual.

Caution/Warning: Refer to accompanying documents for instructions.

GENERAL

All installation, maintenance and service must be performed by qualified
technicians who are familiar with the warnings and instructions of this manual.

Use of the equipment in a manner not specified by the manufacturer can impair
the protection provided within.

The enclosure cover must remain closed at all times during operation to ensure
safety of personnel. The cover may be opened using a screwdriver; however,
only authorized personnel or technicians should be allowed to open and service
the unit.

DynAmp, LLC does not assume liability for the customer’s failure to comply with
the rules and requirements provided in this manual.

HAZARDOUS

VOLTAGE

This equipment is designed to be connected to hazardous electric voltages.
Ignoring the installation precautions and warnings can result in severe personal
injury or equipment damage.

To avoid the risk of electrical shock or fire, the safety instructions and guidelines
in this manual must be followed. The electrical specifications must not be
exceeded and the unit must be installed according to directions provided.

This equipment is intended for indoor or outdoor use. It should be mounted in a
well-ventilated area, away from high heat, dust, and corrosive atmosphere. The
ambient temperature must not exceed specified limits.

For mounting considerations that fall outside the recommended specifications
provided in this manual, the factory should be contacted for approval.

This unit is rated for installation category II and pollution degree 2.

INSTALLATION

«
...
3
4
5
6
7
...
»

Содержание LKAT2














































Отзывы:

Нет отзывов