Dynamix 4-Band VDSL CO/CPE Modem Скачать руководство пользователя страница 24

4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 

 

                                                                                                                                                                                                                                                                   

 

24

 

Important Safety Instructions 
 

Caution

The direct plug-in wall transformer serves as the main disconnect for the product. The socket outlet shall be installed near 

the product and be readily accessible. 

Caution

Use only the power supply included with this product. In the event the power supply is lost or damaged

In the United States, 

use only with CSA certified or UL listed Class 2 power supply, rated 5Vdc 1A or above. 

IN Europe, use only with CE certified power supply, rated 5Vdc 1A or above. 

Do not use this equipment near water, for example in a wet basement. 

Avoid using a telephone during an electrical storm. There may be a remote risk of electrical shock from lightning. 

Do not use the telephone to report a gas leak in the vicinity of the leak. 

If trouble is experienced with this unit, please contact customer service at the address and phone listed below. Do not disassemble this 
equipment. It does not contain any user serviceable components.

 

 

FCC Warning 
 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own 
expense. 
 
 

Содержание 4-Band VDSL CO/CPE Modem


























Отзывы: