Dynamatic 15-533-1015 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 14

Dynamatic 15-533-1015 Скачать руководство пользователя страница 1

1

Instruction Sheet

IS-539-15

revised 2019

15-533-1015 Panel Mount 4000 (4.3 A Controller)

15-551-1015 Standard Enclosure 4000 (4.3 A Controller)

15-539-0015 Panel Mount 4050 (8 A Controller)

15-553-0015 Standard Enclosure 4050 (8 A Controller)

Model 4000 and 4050 with Torque Limit and Jog at Run Speed

Introduction

These instructions relate specifically to
the model 4000 and 4050 controllers
assembled for Speed Control with
Torque Limit and Jog at Run Speed
modification. Connection diagram,
schematic diagram, switch
programming, plug wiring connection,
adjustment procedure and
recommended spare parts list for these
specific assemblies are contained in
this Instruction Sheet. Any differences
between these two controllers are
clearly noted. Use Instruction Manual
IM-130006-83XX with this Instruction
Sheet for complete installation,
operation and maintenance
instructions.
Caution: Above ground electrical
potentials scan be hazardous. Always
disconnect electrical power before
working on the controller.
*Heat sink assembly, HS1, and its
wiring are only supplied on 4050
controls. The parts are mounted on the
15-530-5 main 4000 boards.

Drive Source International/Dynamatic

7900 Durand Ave Bldg 3 Sturtevant, WI 53177

800-548-2169 •

[email protected]

www.Dynamatic.com

1
2
3
...
»

Содержание 15-533-1015















Отзывы:

Нет отзывов