Page 4
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
Page 5
M2011MOUNTING
MODEL 2011 & 3000LC SINGLE
OUTSWING ELECTROMAGNETIC LOCK
INSTALLATION INSTRUCTIONS
12/10
705 Emmett Street Bristol, CT 06010
1-877-DynaLock www.dynalock.com
MOUNTING THE ARMATURE
Mount the Armature Housing to the door using four (4) #8 x 1” sheet metal screws or #8-32 x 3/8” machine
screws.
Place the Armature inside the Armature Housing and secure using the proper hardware, according to the above
illustrations. Firmly tighten the Armature mounting screw with a 3/16” hex wrench.
Failure to properly secure the Armature to the door could result in serious injury or possible security
breach.
From the three illustrations below select the one that resembles your door type and follow the instructions for drilling
the Armature mounting screw hole. (See Template)
Drill four (4) 1/8” dia. holes for #8 x 1” sheet metal screws or drill and tap for #8-32 x 3/8” machine screws (See
Template).
GLASS AND ALUMINUM
OR HOLLOW METAL DOOR
SOLID CORE DOOR
REINFORCED DOOR
Drill an 11/32” diameter hole
through the door. From the
sex nut side only enlarge the
hole to 21/32” diameter.
Drill an 11/32” diameter hole
through the door. From the
sex nut side drill 1/2” diameter
hole to 1” depth.
Drill a 17/64” diameter hole
and tap for 5/16-18 thread
ARMATURE
STEEL WASHER
ARMATURE
SCREW
D O O R
SPACER
SEX
NUT
21/32"
ARMATURE
HOUSING
ARMATURE
SPACER
STEEL WASHER
ARMATURE
SCREW
ARMATURE
SPACER
1/2"
1"
ARMATURE
ARMATURE
HOUSING
STEEL WASHER
ARMATURE
SCREW
ARMATURE
SPACER
5/16"-18 THREAD
ARMATURE
ARMATURE
HOUSING
1/4” MIN
MOUNTING THE LOCK
1) Mounting the baseplate to the header:
Separate the baseplate from the lock housing with the Hex wrench.
Place the baseplate against the header with the counter sunk slots
visible, and the large slot over the wire hole. Using an electric drill
with a Philips bit attach the baseplate to the header at both slotted
locations with the screws provided. Tighten the screws just snug
enough to allow for final adjustments.
2) Aligning the lock and armature:
Close and latch the door. Temporarily mount the lock to
the baseplate and verify the lock face and the armature
are making full contact for the entire length of the arma-
ture. If any adjustment required gently tap the baseplate
with a soft mallet until full contact is achieved. Mark
the two baseplate corner locations lightly with a pencil
for reference. Remove the lock from the baseplate and
tighten both adjustment screws. Drive the remaining 5
screws into the header using the baseplate as a physical
template. Screw heads must not project above the baseplate.
3) Attaching the lock to the baseplate:
Using the Hex wrench, permanently fasten the lock to
the baseplate with the two 1/4” - 20 x 1-1/4” machine
screws removed in step 1. Install the plug caps over
the mounting screws with a small mallet.
BASEPLATE
HEADER
ARMATURE &
LOCKFACE MUST
MAKE FULL CONTACT
MAGLOCK
SHOULD BE PARALLEL
LOCK
PLUG
CAPS
SOCKET HEAD
MOUNTING SCREWS
