manualshive.com logo in svg

DynaGen BCM-12, Инструкция по установке и эксплуатации

Поделиться
Скачать
DynaGen BCM-12 Скачать руководство пользователя страница 2

 
 

2

 

Thank You For Purchasing This DynaGen Product

 

 
Please Read Manual Before Installing Unit

 

 
 
 
 
Receipt of Shipment and Warranty Return Information 

 

Upon receipt of shipment, carefully remove the unit from the shipping container and thoroughly 
examine the unit for shipping damage. In case of damage, immediately contact the carrier and 
request that an inspection report be filed prior to contacting DynaGen.  
 
All returned items are to be shipped prepaid and include a Return Material Authorization (RMA) 
number issued by DynaGen.  RMA forms are available by contacting DynaGen Technical 
Support through the contact methods listed below. 

 
Limited Warranty  
 

DynaGen will repair or replace any BCM, which proves to be defective under normal and proper 
use within 

Two Years

 from the date of shipment. This constitutes the only warranty and no other 

warranty shall be implied.  

 
 
 
 
 
 
 
 

 

 
We welcome your comments and suggestions. Please contact us at: 
 

DynaGen Technologies Inc. 
Phone: 1-888-396-2436 

(902) 562 0133 

Fax:     (902) 567 0633 
Email: [email protected]

 

WEB SITE: www.dynagen.ca

 

 
 
 
 

Operating & Installation Manual for Battery Charge Monitor (BCM)

 

Содержание BCM-12















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды