2
5. When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W."
These cords are rated for outdoor use and reduce the
risk of electric shock.
Personal Safety
1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs,
alcohol, or medication.
A moment of inattention while operating power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts.
Loose clothes,
jewelry, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure switch is off before plugging in.
Carrying tools with your finger on the switch or plugging in tools that have the switch
on invites accidents.
4. Remove adjusting keys or switches before turning the tool on.
A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enables better control of the tool in unexpected situations.
6. Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
Tool Use and Care
1. Use clamps or other practical way to secure and support the workpiece to a stable platform.
Holding the work by hand or against your body is unstable and may
lead to loss of control.
2. Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate for which it is designed.
3. Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is dangerous and must be repaired.
4. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures
reduce the risk of starting the tool accidentally.
5. Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
6. Maintain tools with care. keep cutting tools sharp and clean.
Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.
7. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the
tool serviced before using.
Many accidents are caused by poorly maintained tools.
8. Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous
when used on another tool.
Service
1. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.
Use of unauthorized parts or failure
to follow Maintenance Instructions may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a "live"
wire will make exposed mental parts of the tool "live" and shock the operator.
(See Definitions for label symbols on pg. 4)
TOOL DESCRIPTION
Dynafile II
– Is an electric hand tool with a moving sanding belt, tool includes: an on/off switch, side handle, Dynafile II Belt Sanding Head Assembly, and is equipped
with a 8 ft. cord set.
ASSEMBLY and OPERATION INSTRUCTIONS
1.
With power source disconnected from tool rotate head to desired position and tighten set screw with hex wrench provided to clamp.
2.
Connect power source to tool. Be careful not to depress switch in the process.
3.
Hold tool by the motor housing only. One or two hands may be used. Do Not hold tool by head/housing assembly. Keep hands away from all grinding/sanding edges
and moving parts. A side handle is included for two hand operation of tool. (See "Installing Side Handle" Instructions.)
4.
Slide and rock slide switch forward to start tool. Touch rear of slide switch to release.
5.
While tool is running, adjust belt tracking by turning
95218
Rough Adjustment Knob to the left or right accordingly, so as abrasive belt rides evenly over contact arm.
6.
Always work off the return side of the abrasive belt. This will ensure superior tracking and reduce downtime of tool.
MAINTENANCE and ACCESSORY CARE INSTRUCTIONS
Important:
A preventative maintenance program is recommended whenever portable power tools are used.
•
Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify
Model #
,
Serial #
and
SFPM
of your tool.
Routine Preventative Maintenance:
•
Mineral spirits are recommended when cleaning the Dynafile II Assembly. Do not use on electrical components or clean tool or parts with any solvents or oils containing
acids, esters, ketones, chlorinated hydrocarbons or nitro carbons. Blow the dirt from electrical components with air.
•
DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
®
).
•
Tool labels must be kept legible at all times, if not, send tool in for relabeling. User is responsible for maintaining specification information i.e.:
Model #, S/N, and SFPM. (See Assembly Breakdown)
•
Visually inspect plugs and cords for frays, visible damage and signs of deterioration. Replace damaged or worn components.
•
Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No.
95903
) for safety information.
•
Brush Changing – When the brushes wear down to a predetermined length, the tool is automatically shut off to prevent damage to the armature. Unplug tool and
remove brush caps (item #23) and replace brushes (item #22). Replace brush caps.
After maintenance is performed on tool check for excessive tool vibration. Check for excessive current leakage at 550 volts with a current leakage tester on all screws and
the gear case, if the electrical components have been disturbed during repair.
Handling and Storage of Tool and Accessories:
•
Use of tool rests, hangers and/or balancers is recommended.
•
DO NOT carry tool by cord.
