57083
Vacuum Adapter
57065
Cone Muffler
57066
Muffler Body
95526
O-Ring
96197
Dowel Pin
57068
Vac Nozzle
57067
Vac Tube
Machine Exhaust Assemblies
Self Generated Vacuum (Vac-Ready) / Machine Exhaust
For Models: 57861, 57862, 57863
(PD01•33)
2
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Warning:
Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important:
All Dynabrade rotary vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning:
Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1.
With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2.
Install air fitting into inlet bushing of tool.
Important:
Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid
damaging valve body housing.
3.
Connect power source to tool. Be careful not to depress throttle lever in the process.
4.
Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
Maintenance Instructions:
1.
Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to
correct the cause before use.
2.
Some silencers on air tools may clog with use. Clean and replace as required.
3.
All Dynabrade Rotary Vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the
tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N
95842
: 1pt. 473ml.)
is recommended.
4.
An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following:
11405
Air Line
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic
components. Operates 40 SCFM @ 100 PSIG with 3/8" NPT female ports.
5.
Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the
Model #
,
Serial #
, and
RPM
of your machine.
6.
A Motor Tine-Up Kit (P/N
96024
) is available which includes assorted parts to help maintain motor in peek operating condition.
7.
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones,
chlorinated hydrocarbons or nitro carbons.
57093
Vacuum Adapter
57065
Cone Muffler
57066
Muffler Body
56027
Muffler Insert (2)**
56028
Muffler Cap
57065
Cone Muffler
57066
Muffler Body
56027
Muffler Insert (2)**
56028
Muffler Cap
Central Vacuum / Machine Exhaust
For Model: 57864
Non-Vacuum / Machine Exhaust
For Model: 57860
** Muffler inserts available in Package of 30 - P/N
56054.
•
Important:
User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
•
Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.
•
Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
•
Inspect abrasives/accessories for damage or defects prior to installation on tools.
•
Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No.
95903
) for more complete safety information.
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
Model
Motor
Motor
Air Inlet
Sound
Air Flow Rate
Air Pressure
Hose I.D.
Weight
Length
Height
Number
HP (W)
RPM
Thread
Level
CFM/SCFM (LPM)
PSIG (Bars)
Inch (mm)
Pound (kg)
Inch (mm)
Inch (mm)
All Models
.18 (134)
10,000
1/4" NPT
83 dB(A)
3/18 (510)
90 (6.2)
1/4" (8 mm)
2.75 (1.2)
7-1/4 (184)
4-1/4 (108)
