Dyacon MS-100 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 22

Dyacon MS-100 Скачать руководство пользователя страница 7

DYACON Quick-start Guide

Mechanical Setup and Installation

3.0 Mechanical Setup and
Installation

3.1.1 Required Tools

Installation tools depends on the mounting location. For purposes of this manual, it is assumed
that CM-1 will be used with Dyacon MS-100 weather stations and mounted on Dyacon
Tripod-1.

Control Module

8 mm (5/16 inch) socket for band clamps

Phillips #2 driver for Control Module cover

0.10” to 0.13” (2.5 mm to 3.5 mm) wide slotted driver (

included with control module

) for

screw terminals

Tripod

5.5 mm (7/32 inch) nut driver (

included with tripod

) or open-end wrench wrench for guy cable

clips.

8 mm (5/16 inch) open-end wrench for turnbuckle lock nuts.

Hammer for stakes or tools appropriate for other mounting method, as required.

WSD-1

Phillips #2 driver to attach wind vane and pole set screw

TPH-1

8 mm (5/16 inch) socket or slotted driver for band clamps

Crossover

8 mm (5/16 inch) socket or slotted driver for band clamps

Solar Panel Bracket

8 mm (5/16 inch) socket or slotted driver for band clamps

Rain Gauge

8 mm (5/16 inch) socket or slotted driver for band clamps on bracket

4 mm (5/32 inch) hex wrench (

included with gauge

) to remove rain gauge top.

13 mm (9/16 inch) open-end wrench or adjustable open-end wrench for leveling screws.

Other

Wire cutters for electrical cable prep and cable ties

Wire stripper for 24 AWG to 22 AWG wire

Page 7/22

«
...
5
6
7
8
9
...
»

Содержание MS-100























Отзывы:

Нет отзывов