- 3 -
M965535 Rev. 1.3 (4/15)
5
3
4
TEST INSTALLED FAUCET
INSTALL HOSE AND SPRAY (Model D35402.001)
MAKE WATER SUPPLY CONNECTIONS
• Move HANDLE
(1)
into “off” position.
• Turn on water supplies and check all connections for leaks.
• Pull HAND SPRAY
(2)
from HOLDER
(3)
and disconnect HAND SPRAY
(2)
from HOSE
(4)
. Pull HOSE
(4)
(HOSE should pull approximately
2 feet)and direct open HOSE END
(4)
into sink.
• Operate handle, in COLD and HOT positions, to flush
water lines thoroughly.
• Connect HAND SPRAY
(2)
to HOSE END
(4)
. Place
HAND SPRA
Y (2)
back into HOLDER
(3)
, operate
HANDLE
(1)
and check all connections for leaks.
• Check HAND SPRAY
(2)
operation with faucet on
push front of LEVER
(5)
for a broad cleansing spray.
TROUBLE SHOOTING
Low water flow from faucet:
• Remove AERATOR
(6)
and clean if necessary.
Pull-Out Spray will not remove from faucet freely:
• Check that pull-out spray hose is not obstructed with
plumbingconnections or fittings under faucet.
• Remove LARGE WASHER
(5)
and SMALL WASHER
(6)
FROM SPRAY HOSE
(7)
.
Feed the small end of the SPRAY HOSE
(7)
through the SPRAY HOLDER
(1)
.
Install the SMALL WASHER
(6)
into the COUPLING
(9)
of the spray connection
on faucet. Connect HOSE END
(7)
to COUPLING
(9)
.
• Install the LARGE WASHER
(5)
into the COUPLING
(10)
for the HAND SPRAY
(8)
and hand tighten. Place the HAND SPRAY
(8)
into the Spray holder
(1)
.
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLIES
(6, 7)
directly to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect left supply (Marked Red) to Hot and
right supply (Marked Blue) to Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
• Faucet supplies are 21" long from faucet base.
Note: If additional supply length is required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (6, 7) are too long, loop asillustrated to avoid kinking.
• Remove RUBBER WASHER
(5)
and FIBER WASHER
(6)
FROM SPRAY HOSE
(7)
. Feed
the small end of the SPRAY HOSE
(7)
through the SPRAY HOLDER
(1)
. Install the FIBER
WASHER
(6)
into the COUPLING
(9)
of the spray connection on faucet. Tighten with two
wrenches to make a water tight connection.
• Install the RUBBER WASHER
(5)
into the COUPLING
(10
) for the HAND SPRAY
(8)
and
hand tighten. Place the HAND SPRAY
(8)
into the Spray holder
(1)
.
2
INSTALL SPRAY HOLDER (Model D35402.001)
• Apply a bead of putty to the underside lip of SPRAY HOLDER
(1)
.
• Place the SPRAY HOLDER
(1)
into the appropriate mounting hole.
Assemble the RUBBER WASHER
(2)
, BRASS WASHER
(3)
and
LOCK NUT
(4)
onto the shank of SPRAY HOLDER
(1)
. From
below tighten LOCK NUT
(4)
to secure SPRAY HOLDER
(1)
.
9
PUTTY
1
10
5
8
2
3
4
COLD
HOT
SUPPLY STOPS
6
7
6
7
2
3
5
1
4
6
