background image

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017

5"

(127 mm)

5"

(127 mm)

6"

(151 mm)

9-7/8"

(250 mm)

MTG.

SURFACE

25-3/4"

(655 mm) 

2-7/16"

(62 mm)

3/8" (10 mm)

SUPPLIES

3/8" (10 mm)

SUPPLIES

2-7/16"

(62 mm)

9-3/8" MAX.

(238 mm)

1-1/4" O.D.

(32 mm) 

NOTE: MOUNTING HOLE

1-3/8" DIA. (35 mm)

13-5/8"

(346 mm)

9-3/4"

(247 mm)

MTG.

SURFACE

22"

(558 mm) 

50 mm MAX.

50 mm MAX.

9-3/8" MAX.

(238 mm)

MAX 2"

(51 mm)

MAX 2"

(51 mm)

1-1/4" O.D.

(32 mm) 

SA

VE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing 
supply stores. It is essential that the tools and materials be on hand before work is begun.

M965474 Rev. 1.5 (3/17)

Monoblock Vessel 

Model D35104150

Monoblock 

Model D35104100

Keefe

®

  

Single Lever Faucet 

Flat Blade Screwdriver    

Plumber’s Putty or Caulking

Adjustable Wrench    

Tubing Cutter 

Channel Locks

ROUGHING-IN DIMENSIONS: 

NOTE:

 Mounting holes are 1-3/8

"

 D.

In the United States:

DXV

One Centennial Avenue 

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty 

information may also be obtained by calling 

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV 

5900 Avebury Road  

Mississauga, Ontario  

L5R 3M3 

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093 

Fax: 1-800-395-1498 

www.DXV.ca

In Mexico:

DXV 

Via Morelos 330 

Col. Santa Clara Coatitla  

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your 
installation proceeds smoothly, please read these 
instructions carefully before you begin.

Содержание Keefe D35104100










Отзывы: