Dwyer Instruments TAC3 series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 28

Dwyer Instruments TAC3 series Скачать руководство пользователя страница 2

Diode Laser

Max. output power:

<1 milliwatt

Wavelength:

650 nanometers (visible light)

Min. divergence:

1.0 milliradian

Output:

Continuous (CW)

Laser hazard classifi cation:

Class 2

Contact info: www.dwyer-inst.com
Country of Origin: USA

SAFEGUARDS AND PRECAUTIONS

Laser hazards

• Eye injury from beam

- Do not look into the direct or refl ected beam; can cause eye injury

up to 25 ft (7.5 m) away.

• Visual interference (glare) with pilots and drivers

- Interferes with vision up to 525 ft (160

m) away. Can be a distraction up to 1 mile (1.6 km) away.

NEVER point any laser towards

aircraft or vehicles; it is unsafe and illegal.

Safe use guidance

Class  2  lasers  are  considered  safe  for
accidental  eye  exposure.    Do  not  look  or
stare  into  beam.    Do  not  aim  at  aircraft.

This is not a toy.

Always supervise children.

Read and follow all instructions in this manual carefully, and retain
this manual for future reference.

Do not use this instrument in any manner inconsistent with these operating
instructions or under any conditions that exceed the environmental
specifi cations stated.

This instrument is not user serviceable. For technical assistance, contact the
sales organization from which you purchased the product.

In order to comply with EU Directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE):

This product may contain material which could

be hazardous to human health and the environment. DO NOT DISPOSE of this
product as unsorted municipal waste. This product needs to be RECYCLED in

accordance with local regulations, contact your local authorities for more information. This
product may be returnable to your distributor for recycling - contact the distributor for details.

«
1
2
3
4
...
»

Содержание TAC3 series





























Отзывы:

Нет отзывов