22
English
Installation and removal protective plate (see fig. 4)
Fig� 4 shows protective plate
25
mounting / dismounting
operations�
Setting of cutting angle (see fig. 5)
•
Loosen adjusting bolts
16
with help of wrench
15
(see fig. 5.1).
•
Set the required cutting angle turning adjusting
stop
17
� The angle is set according to the indication of
scale
28
(see fig. 5.2)
�
•
Tighten adjusting bolts
16
with help of wrench
15
(see fig. 5.3).
Setting of cutting width (see fig. 6)
•
Unscrew adjusting bolts
16
with help of wrench
15
(see fig. 6.1).
•
Select the required width of cut shifting the adjusting
stop
17
(see fig. 6.2).
•
Align holes in the adjusting stop
17
with threaded
holes in the base plate
11
, and tighten adjusting
bolts
16
with help of wrench
15
�
Mounting / replacement of cutting disc (see
fig. 7-10)
After mounting of cutting disc, make a
trial run before commencing operation -
start the power tool and let it work in idle
mode for not less than 30 seconds. The
operation of cutting disc with radial or axial run-
out and causing increased vibration of the power
tool is strictly forbidden.
Wearing protective gloves is recom-
mended for mounting / replacing cutting
disc.
•
Lift the body to the uppermost position�
•
For model
SDS21-355 DN
� Loosen the wing screw
22
and move the cover
23
upwards, as shown in figure 7.1.
•
For model
SDS24-355 DN
� Lift the movable guard
cover
9
to the uppermost position (see fig. 9.1).
•
Move the spindle lock
8
to the right and hold it, after
that put the wrench
15
on the bolt
33
and turn it in order
to fix the cutting disc
10
in the fixed position. Press and
hold the spindle lock
8
, unscrew the bolt
33
with help
of wrench
15
(see fig. 7.2, 9.2).
•
Dismount from the spindle
29
: washer
32
, external
flange
31
, cutting disc
10
and internal flange
30
(see
fig. 8.1, 10.1).
•
Clean fastening elements with a soft brush and
mount on the spindle
29
: internal flange
30
, cutting
disc
10
, external flange
31
and washer
32
� Observe the
consequence of parts installation, avoid oblique setting
of parts in the course of mounting and do not turn over
the flanges (see fig. 8.2, 10.2).
•
Press and hold the spindle lock
8
, tighten the
bolt
24
with help of wrench
15
� Then release the
spindle lock
8
�
•
Make sure that cutting disc
10
does not touch any
elements of power tool and can rotate freely�
•
For model
SDS21-355 DN
� Move the cover
23
down
and tighten the wing screw
22
�
•
For model
SDS24-355 DN
� Move the movable guard
cover
9
in original location�
Initial operating
of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
tool on / off
Short-term switching on / off
To switch on, press and hold on / off switch
5
, to switch
off - release it�
Long-term switching on / off
Switching on:
Push on / off switch
5
and lock it in the position with
lock-on button
4
�
Switching off:
Push and release on / off switch
5
�
•
Recommendations
on the power tool operation
Place the power tool on the worktable� It's recom-
mended to fix power tool with cramps (see fig. 11).
•
If required, adjust the clamping device for cutting
a workpiece with required width and set the needed
cutting angle (the order of operations is described
above)�
•
Lift the tiltable lever
20
and move the lead screw
19
until its rotary stop
18
touches the workpiece (see
fig. 12.1).
•
Lower the tiltable lever
20
and turn the clamping
handle
21
to fix the workpiece (see fig. 12.2-12.3).
Avoid misalignment or skew of the workpiece�
•
Turn on the power tool, allow cutting disc
10
to reach
the full rotation speed�
•
Smoothly pull the body down and make the cut�
•
Do not overload the power tool (especially when cut-
ting metal profiles, panel constructions, etc.) as it will
overload the motor and may damage the cutting disc�
There must be enough time for the power tool to carry
out the operation�
•
Turn off the power tool and wait until cutting disc
10
stops completely�
•
Lift the power tool body up smoothly�
•
To remove the workpiece, lift the tiltable lever
20
and move the lead screw
19
back�
Power tool maintenance /
preventive measures
Before carrying out any works on the power tool it
must be disconnected from the mains.
Cleaning of the power tool
An indispensable condition for a safe long-term
exploitation of the power tool is to keep it clean� During
the long treatment of metal, current-conducting dust
can be accumulated inside the power tool� Regularly
Содержание SDS21-355 DN
