background image

2-6

Atomix LT Installation Guide

2.2.3  Overview of the Soldering Side

This section shows the operation items located at the soldering side of 
the PCI video board. They can be found at the top left of the soldering 
side:

10 Fail Safe 1

For a bypass of the SDI input signals to the SDI 
outputs in case of power loss; connect either 
this connector or Fail Safe 0 (not available for 
Atomix LT 4 BNC) to a rechargeable battery 
(accu, see section “Technical Data” on 
page A-1)

11 breaking line

The printed circuit board provides at its bottom 
an extension void of any electrical parts; it may 
serve to stabilize the installation of the board in 
a computer system; when not needed or inter-
fering, you can carefully break it off the circuit 
board at the breaking line

12 AUX Breakout

Only available for Atomix LT 4 BNC:

 DB-15 

(VGA-style) connector to connect a proprietary 
breakout cable, providing:

– 2 × XLR connectors for LTC in- and output
– 1 × BNC for reference input
– 1 × DB-9 for RS-422 (i.e. RMT In/Out 1)
– 1 × 3.5 mm unbalanced stereo headphone 

jack for analog audio output

For further details about the connectors see the 
slot panels described in section “Overview of 
the Panels” on page 2-10 on which the con-
nectors are available

13 Accessory

Only available for Atomix LT 4 BNC:

 Flat cable 

connector for a connection to a general pur-
pose interface (GPI); this connector is located 
on the rear side of the expansion module 
mounted to the PCI video board

No.

Item

Explanation

Содержание Atomix LT









































































Отзывы: