/fin t:
On most bookshelf-type or compact stereo systems, inserting a headphone
into the headphone jack results in automatic cutoff of the regular, or hard-wired,
speakers.
Most TVs, regardless of age or price, have variable outputs.
you are unsure
which, if any of your outputs is fixed, refer to the TV instruction manual. Some
TVs have outputs that can switch between variable and fixed. Refer to the TV
instruction manual. When given a choice, fixed is a/ways recommended.
POWER THE SPEAKERS
Select from the following options to power the
speakers.
P
OWER
O
PTION
1
C
ONNECT
THE
AC
A
DAPTER
Turn the speaker Power On-Off/Volume
Control Wheel (D) to the “OFF” position (atl
the way counterclockwise).
Inset-t the power cord from the AC adapter
(P) into the Speaker Power Input Jack (F).
Plug the AC adapter into any standard wall
outlet.
Repeat for other speaker.
Note: Be sure to use the AC adapters rated 15V DC
800
P
OWER
O
PTION
2
I
NSERT
C
ELL
Remove the four screws holding the battery
compartment cover(E).
Inset-t eight (8) “C” batteries (optional) into the
speaker following the polarity (“t” and
as
diagrammed in the battery compartment.
Replace the battery compartment cover and
SC
rews.
Repeat for other speaker.
ADJUST THE TRANSMITTER
Adjust the transmitter as follows:
STEP 1
T
URN
ON
YOUR
A
UDIO
S
OURCE
1. Turn ON your audio source (i.e. Stereo Receiver, TV, etc.) so that you can hear
sound coming from the source.
7
STEP 2
S
ET THE
“L
EVEL
”
Set the Frequency Control Wheel (N) to
midpoint.
Turn the Output Level Control wheel (K) all the way to
the right as shown.
Check status df Audio Level Indicator Light (H). If it
flickers intermittently (about half the time), proceed to
“Tune the Speakers”.
Audio Level
Indicator Light
Turn to
Right
If Audio Level Indicator Light is on solid red or flickering
very rapidly, turn wheel slowly back to the left until light
flickers intermittently.
Output Level
Frequency
Note: the light does not flicker, confirm secure connection
Control
Control
of the AC adapter: the light
does not flicker,
Wheel
Wheel
confirm secure connection to the audio source output.
there is
no response, leave the Output Level
Control Wheel completely to the right shown) and proceed.
Hint:
the transmitter is connected to a variable output (i.e. Headphone Jack, TV audio
out) on the audio source,
leave
the Output Level Control Wheel turned
a// the
way
to the right
(as
shown) and adiust the volume on the audio source or down as
to make the Audio
indicator Light flicker intermittently.
TUNE THE SPEAKERS
Adjust the speakers as follows:
T
URN
O
N AND
T
UNE
THE
S
PEAKERS
1. Use the speaker Power ON-OFF/Volume Control Wheel (D)
to turn the speaker “ON.” Tuning Indicator Light (A) will
Tuning Indicator
Light
illuminate red.
2. Turn the Tuning Control Wheel (B) until the audio source
is heard. The Tuning Indicator Light (A) will change
color to green, indicating the speaker is tuned to the
signal from the transmitter.
3. Adjust
volume
as desired.
4.
Set the
Switch (C) accordingly (see
“Setting the Speakers for Stereo/Monaural
Operation” on page 9).
5. Repeat process for other speaker.
Note: Interference in the form of static and/or
distortion can sometimes be heard. If this
Power
occurs,
confirm correct transmitter/speaker adjustments and
Control Wheel
indicators. If the problem persists, refer to TROUBLESHOOTING.
