background image

16                                                       

 

 

DVDO-Xtend-TX100_V1.0 0 

DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter

 

User Manual

                  

DVDO

 

 

DVDO

 

Product Configuration Tool 

The  transmitter  supports  configuration through the “DVDO  Product 
Configuration Tool”. 
1.  Connect the HDBT OUT of the transmitter and your receiver HDBT IN, the 

transmitter can be powered by receiver via Cat X cable. 

2.  Use the Micro USB-B to USB-A cable provided to connect the transmitter 

UPDATE port and your PC USB port. Or connect a PC to RS232 port of 
receiver. 

3.  Check which port on the computer the cable is connected to in the device 

manager. 

4.  Copy the “DVDO Product Configuration Tool” to local file. 
5.  Run the tool, and set the connection parameters correctly before sending 

any commands to the transmitter. 

 

Select right port from the drop-down menu, and set the baud rate, then 
press Connect. Once connected you can set the RS232 output port 
commands and the relay mode.   

Note:

 When connect the PC via UPDATE port of the transmitter, the Baud 

Rate is fixed according to the transmitter, and connect PC via RS232 port 
of Receiver, you can set baud rate. 

Содержание DVDO-Xtend-TX100




















Отзывы: