background image

  

 
 

12 

7.

 

Maintenance 

IMPORTANT WARRANTY INFORMATION 

There  are  no  user-serviceable  parts  inside  the  camera.  Removing  the  rear  cover  of  the  camera 
without express authorization from DVC Company will void the camera warranty. 

DVC  professional  cameras  are  manufactured  in  a  clean  environment.  Before  shipping,  each  camera  is 
tested to assure that it meets stringent specifications for cleanliness and quality. 

7.1.

 

Cleaning Guidelines 

Frequent lens changes, especially without careful attention to contaminants, can allow debris to 
accumulate  on  the  infra-red  blocking  filter  and  lens  surfaces.  Therefore,  DVC  Company 
provides the following guidelines for cleaning those components. 
 
To minimize the need to clean the optical surfaces, do not remove the protective lens mount cap 
shipped  with  the  DVC-4000  camera  until  you  are  ready  to  mount  the  camera  to  the  optical 
system. 

7.1.1.

 

Cleaning the lens or optical assembly 

Please follow the lens manufacturer’s recommendations for cleaning. DVC Company is 
not responsible for any damage caused to a lens or optical assembly caused by customer 
cleaning or misuse. 
 
To ensure optimum image quality with any DVC camera, do not remove the protective 
lens-mount  cap  until  ready  to  mount  the  camera  on  the  application.  If  the  camera  is 
removed from the application, immediately replace the cap. Doing so will keep dust and 
other  contaminants  from  accumulating  on  the  optical  surfaces.  In  addition,  please  note 
the following model-specific guidelines. 

7.1.2.

 

Standard (non-cooled) camera precautions 

While  the  lens  mounting  ring  and  locking  flange  allow  the  user  some  lens  back-focus 
adjustment, complete removal of the ring will expose the CCD faceplate and will likely 
cause  debris  to  accumulate  on  its  surface. 

Extreme  care  should  be  taken  to  avoid 

completely removing the lens mounting ring and exposing the CCD faceplate unless 
absolutely  necessary.  Fingerprints  or  other  evidence  of  contact  with  the  CCD 
faceplate may void the warranty. 

7.1.3.

 

TE-Cooled camera precautions 

The  DVC  Thermoelectrically-cooled  cameras  contain  the  CCD  in  a  sealed,  gas-filled 
chamber  having  an  anti-reflective  glass  window. 

Do  not,  under  any  circumstances, 

loosen or remove the inner glass window from a cooled camera

. Doing so will void 

the warranty. If it is suspected that the seal has been broken or if the window breaks, call 
DVC  Customer  Service.  Do  not  apply  power  to  the  camera.  Moisture  will  have  been 
introduced  into  the  chamber,  and  cooling  in  the  presence  of  moisture  will  cause 
condensation and frost on the CCD, which can damage the entire cooling unit. 

Содержание DVC-4000



























Отзывы: