manualshive.com logo in svg

DVB FBGX-01, Руководство по установке изделия

Поделиться
Скачать
DVB FBGX-01 Скачать руководство пользователя страница 7

INSTALLATION 

MANUAL

855-680-9595

NEED HELP?

STEP

 10

STEP

 11

Next you are ready to tighten down 
all the current components. We used 

a floor jack and raised the center 

section until the winch plate brackets 
were straight. These were tightened 
down and secured.  

Next, secure the six M12 bolts 
that attach the winch plate to the 
brackets. Then you will move to the 
skid plate brackets. 

Lastly you will secure the center 
section. Ensuring the center is even 
between the chrome accents. Lift up 
and push back as far as the center 
section allows and secure the six M12 
bolts in place.

Once the center section is completed, 
we will move to the wings. The factory 
lights are utilized. These are simply 
removed by the single 10mm bolt in 
the middle of the light. Use this same 
bolt to attach to our bracket. Once 
the light is in place, use the provided 
M6 bolts to secure the light/bracket

 

combo in place. With light pressure, 
push the bracket and tighten down 
and secure in place.

Содержание FBGX-01












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды