background image

Owner’s Manual – Solar Water Heaters

24

H3165    029664    Rev. B

Five Year Service:

This service should only be carried out by a 
licensed tradesperson. We recommend your 
local Dux Service Agent.

In locations where the water has Total 
Dissolved Solids (TDS) exceeding 600 mg/L, 
this service is recommended every 3 years.

This service should include the following:

•  Replace the PTR Valve.
•   Replace the anode. Ensure the new anode 

is suitable for the water conditions. Please 
refer to page 9 for further information.

•   Inspect and flush the expansion control 

valve (if installed). 

•   Drain and flush the water heater as 

described on page 20.

•   Flush the solar collectors as described on 

page 21.

•   Inspect the condition of any electrical 

conduit and the water heater electrical 
covers. Replace any damaged 
components. 

•   Inspect the insulation on the solar flow 

and return pipes. Repair or replace any 
damaged insulation.

•   Clean the solar collector surface.

Replacement parts are available from your 
local Dux supplier.

Solar Collectors:

The efficiency of the solar collectors will be 
reduced if the glass becomes dirty.

It is recommended that cleaning is carried 
out early in the morning before the sun starts 
to heat the collectors. The easiest way to 
clean the glass is by washing it down with 
water from a hose.

If a more thorough clean is required, safe 
access will be required to the collectors. 
This will usually require the use of a safety 
harness by personnel trained in working 
safely at heights. The collector glass can 
then be cleaned with water, a soft cloth and 
a domestic glass cleaner if required. 

Do not attempt to replace broken collector 
glass. It is not possible to replace the glass 
in a flat plate collector. It may be possible 
to replace the glass in an evacuated tube 
collector. Please contact Dux After Sales and 
Service for further information and advice.

System Maintenance

Содержание Ecosmart 250DP0





































Отзывы: