manualshive.com logo in svg

Durr Dental Tornado 1, Инструкция по установке и эксплуатации

Поделиться
Скачать
Durr Dental Tornado 1 Скачать руководство пользователя страница 38

13 Maintenance

Prior to working on the unit or in case of danger, disconnect it from the mains.

CAUTION
Risk of infection due to burst filters

Particles enter the compressed air network and can therefore enter the mouth of the patient.

❯

Replace filters in accordance with the maintenance schedule.

13.1 Maintenance schedule

NOTICE
Risk of damage to the unit due to blocked filters

Continuous running due to reduced delivery. Damage to the unit due to burst filters.

❯

Replace filters in accordance with the maintenance schedule.

Every time you work with the unit, check it visually for damage to ensure safe and reliable opera-
tion. Damaged units must not be taken back into use.

Unit without membrane-drying unit

Maintenance
interval

Maintenance work

At regular intervals

❯

Drain the condensation water – daily if the humidity is high.

Annually

❯

Replace the air intake filter – every six months if the concentration of dust is
high.

Every 5 years

❯

Replace the vibration dampers.

❯

Change the cup seal.

In accordance with
national law

❯

Check the safety valve.

❯

Carry out recurring safety inspections (e.g. pressure tank inspections, electrical
safety inspections) in accordance with applicable national laws.

Unit with membrane-drying unit

Maintenance
interval

Maintenance work

At regular intervals

❯

Empty the collector tray under the membrane drying unit (the interval may vary
depending on the ambient conditions and method of working; empty it daily if
the humidity is high).

Annually

❯

Replace the air intake filter in the compressor unit – do this every six months if
there is a high concentration of dust.

❯

Replace the fine or sterile filter.

❯

Replace the sintered filter.

Every 5 years

❯

Replace the vibration reducers.

❯

Change the cup seal.

Usage

36

9000-610-60/02 1909V007

EN

Содержание Tornado 1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды