DUROMAX XP12000E страница 32 Скачать руководство пользователя

Страница: 32 / 76

Step 1 - Check the oil

Check the oil

The generator is equipped with an automatic shutoff to

protect it from damage due to low oil. Nonetheless, you

should check the oil level of the engine before each use to

ensure that the engine crankcase has a sufficient amount.

To check the oil level:

Make sure the generator is on a level surface.

Unscrew the oil filler/dipstick cap.

With a dry cloth, wipe the oil off of the stick on the

inside of the cap.

Insert the dipstick as if you were replacing the

cap and then remove it again. There should now be

oil on the stick. If there is no oil on the stick, or oil

only at the very end of the stick, you should add

oil until the engine crankcase is filled (see “Adding

Oil” portion of the “Maintenance” section).

Be sure to replace the cap when finished checking

oil.

BEFORE YOU START YOUR GENERATOR

Model Number

XP12000E

Engine Oil Capacity

37 fl. oz (1.1L)

Содержание XP12000E













































































Результаты поиска

Содержание XP12000E

Отзывы:

Похожие инструкции для XP12000E

Бренды по названию

Популярные бренды

DUROMAX XP12000E, Руководство пользователя

Результаты поиска

Содержание XP12000E

Отзывы:

Похожие инструкции для XP12000E

Бренды по названию

Популярные бренды