background image

SAFETY ALERT SYMBOL

DANGER: This generator produces poisonous carbon monoxide gas when running. This 

gas is both odorless and colorless. Even if you do not see or smell gas, carbon monoxide 
may still be present. Breathing this poison can lead to headaches, dizziness, drowsiness, 
and eventually death. 

 

Use outdoors ONLY in non-confined areas. 

 

Keep several feet of clearance on all sides to allow proper ventilation of the generator.

WARNING: The exhaust from this product contains chemicals known to the State of 

California to cause cancer, birth defects, or other reproductive harm.

WARNING: This generator produces heat when running. Temperatures near exhaust can 

exceed 150°F (65°C). 

 

Do not touch hot surfaces. Pay attention to warning labels on the generator denoting 
hot parts of the machine. 

 

Allow generator to cool several minutes after use before touching engine or areas 
which heat during use.

The safety alert symbol is used with one of the safety words (

DANGER

CAUTION, or WARNING) to alert you of hazards. Please pay attention to 

these hazard notices both in this manual and on the generator.

GENERAL SAFETY PROCEDURES

7

Please familiarize yourself with the following safety symbols and words:

 

DANGER: Indicates a hazard that will result in serious injury or death if instructions are not 

followed.

 

WARNING: Indicates a strong possibility of causing serious injury or death if instructions are not 

followed.

 

CAUTION: Indicates a possibility of personal injury or equipment damage if instructions are not 

followed.

Содержание 991772K1



































































Отзывы: