background image

Assembling the throat plate slide interrogator

6

Additional Instructions 867 M-TYPE - 00.0 - 05/2018

2. Tighten the proximity switch (2) to the metal bracket (4) using the nuts 

and toothed washers:
• The distance between the lower edge of the metal bracket (4) and 

the upper edge of the proximity switch (2) is 

17 mm

• Machine with short thread cutter (KFA): Tighten the proximity 

switch (2) at position (3) (right hole in the metal bracket (4)). 

• Machine with/without thread cutter (FA): Tighten the proximity 

switch (2) at position (1) (left hole in the metal bracket (4)). 

3. Screw the metal bracket (4) into the threaded hole in the hook bearing 

using the screw (5). 

This setting requires a safe switching distance of approx. 0.5 mm 
between throat plate slide (6) and proximity switch (2). 

Information

Switching distance between throat plate slide (6) and proximity switch (2): 

• Standard switching distance: 0.8 mm 
• safe switching distance: 0.64 mm 

Laying the cable

Fig. 5: Assembling the throat plate slide interrogator (3)

4. Swivel up the machine head (

Operating Instructions

). 

5. Tighten the cable (7) of the proximity switch at the hook support.
6. Lay the cable (7) to the right towards the circuit board along the oil 

line (8). 

(2)    - Proximity switch
(7)

- Cable

(8)

- Oil line

Содержание DAC classic 867





















Отзывы: