background image

Appendix

Service Instructions 512-211-01/532-211-01 - 00.0 - 06/2016

71

14 Appendix

14.1 Software error messages

The remedial measures are to be processed in the order specified.

Error

Meaning

Possible cause

Remedial measures
Process in the order specified!

E

8

Error table data

Unable to read the table 
data

• Save the table data again.

E

1

0

Error sewing pattern 
number

The selected sewing pat-
tern is not saved in ROM or 
is set to non-readable. The 
sewing pattern is "0"

• Press the Reset button to confirm the 

sewing pattern number.

E

3

0

Error needle bar 
position top

The needle bar is not at the 
top position

• Check the connections.
• Turn the needle bar to the top dead center 

position.

E

4

0

Error sewing field 

Sewing field exceeded

• Press the Reset button.
• Check X/Y scaling.

E

4

2

Error scaling

Sewing length is below 
10 mm

• Press the Reset button.
• Check sewing pattern and X/Y scaling.

E

4

5

Error sewing pattern 
data

Sewing pattern data cannot 
be applied

• Press the Reset button.
• Check ROM.

E

5

0

Pause

Reset button pressed while 
sewing.
Sewing machine stopped.

• Press the Reset button.
• Actuate the thread trimmer.
• Restart the sewing process.

E

3

0

2

Error machine head Machine head has moved. • Fold back machine head.

E

3

0

5

Error thread trimmer 
position

Thread trimmer blade not 
at home position

• Set main switch to OFF.
• Check sensor.

E

3

0

6

Error thread catcher 
position

Thread catcher not at home 
position

• Set main switch to OFF.
• Check sensor.

E

3

3

2

Error clamp foot 
position

Clamp foot not at home 
position

• Set main switch to OFF.
• Check sensor.

E

5

0

1

Data read error

Data not available or in the 
wrong format

• Save the data to a USB stick again.

E

5

0

2

USB read error

MOT file error

• Save the data to a USB stick again.

E

5

0

3

SUM read error

CHECKSUM data error in 
MOT file

• Save the CHECKSUM file to a USB stick 

again.

E

5

0

4

End block error

No end block in the MOT 
file

• Save the end block file to a USB stick 

again.

E

5

0

5

USB read error

USB stick not found

• Set main switch to OFF.
• Set main switch to ON.
• Reinsert USB stick.

E

5

0

6

USB read error

Unable to read U01 ~ U10. • Set main switch to OFF.

• Set main switch to ON.
• Reinsert USB stick.

Содержание 512-211-01



















































































Отзывы: