Duratrax WarHead EVO Скачать руководство пользователя страница 8

Страница: 8 / 24

SOME THINGS TO REMEMBER DURING BREAK-IN
1. Run with the body off. This will keep the engine cooler.
2. Keep the air cleaner on at ALL times
3. Run on a smooth, hard surface. An empty parking lot

is perfect.

4. Use the same fuel that you will use for normal running.
5. Resist the urge to accelerate and decelerate quickly.
6. Break-in puts stress on the glow plug and can burn it out.

Make sure you have an extra plug or two on hand.

7. Do NOT overheat the engine (see page 9).You can check the

head temperature by using one of the temperature gauges
that are readily available (DuraTrax

™

Flashpoint, DTXP3100).

TANK 1
Your first tank of fuel should be running the Warhead EVO
at a very rich needle valve setting. This allows the fuel to
carry as much oil as possible into the engine to properly
lubricate the internal parts during the break-in.

1. Open the high speed needle valve 4-1/2 turns from fully

closed (counterclockwise). This is factory set already, but
check it to make sure. When closing the high-speed
needle, close until you feel some resistance. DO NOT
overtighten or you will damage the engine.

2. Fill the fuel tank and start the engine.
3. Run the truck on a smooth surface with the body off.
4. Run back and forth at medium speeds, slowly accelerating

and decelerating the truck. NOTE: It is normal for the two
speed not to shift (see page 10).

5. Run the truck until the tank is almost out of fuel. Do not allow

the tank to run out of fuel during break-in. This leans out the
engine and can cause overheating.

6. Stop the engine and allow it to cool. This normally takes

around 10-15 minutes.

NOTE: If your engine does not stay running consistently,
increase the idle speed by turning the idle stop screw clockwise.

TANK 2
Lean the high-speed needle 1/12 turn from “tank 1” setting.
Run the truck for the complete tank and
then let cool.

TANK 3
Lean the high-speed needle another 1/12
turn from “tank 2” setting. Run the truck
for the complete tank and then let cool.

TANK 4
Lean the high-speed needle another 1/12 turn from “tank 3”
setting. Run the truck for the complete tank and then let cool.
You should notice the engine running much better at this point.

TANK 5
Lean the high-speed needle another 1/12 turn from “tank 4”
setting. Run the truck for the complete tank and then let cool.
The engine is now ready to be performanced tuned.

Important! At this point, the engine will likely be running at
a faster idle speed than needed (This is typical after break-
in). Adjust the idle stop screw to lower the idle speed so that
the wheels do not, or just barely, rotate when you lift the
truck off the ground.

TUNING TIPS
After break-in, run the truck where you plan to do most of your
driving (grass, street, track, etc). Tune the high speed needle
so the engine makes good power without overheating. Using
a temperature gauge, tune the engine so that it will
consistently stay under 270° F (132° C). Keep in mind, RC
engines usually take a minute or two to warm up. It is common
not to reach full power right away. Never tune a cold engine!

If needed, tune the low speed needle so that the truck idles
and accelerates smoothly and consistently. Note: You may
sometimes experience “run-on” when running the truck.
“Run-on” is when the engine does not drop back down to
idle after the trigger on the transmitter is released. To correct
this, richen the low-speed needle using 1/8 turn increments
until the engine idles normally when the trigger is released.

ENGINE CARE
Never store your Warhead EVO with fuel in the tank. We
recommend that after the final run of the day, you empty the fuel
tank and then run the engine at idle until all the fuel is out of the
fuel lines and engine. Remove the air filter and glow plug. Then
place two drops of Hobbico

After Run Engine Oil (HCAP3000)

in the carburetor and two into the cylinder to help prevent
corrosion. Turn engine over a few times to circulate the oil.

10 WAYS TO ENSURE LONG LIFE FROM YOUR ENGINE
1. Keep your engine and air filter clean. Dirt will act as

insulation on an engine. It will not be able to shed heat as
easily. Clean and re-oil the element often.

2. Do not over-lean your engine.
3. Do not run your engine with little or no load. Don’t throttle

up the engine to full throttle when the wheels are not in
contact with the ground.

4. Do not overheat the engine (see page 9).
5. Do not use a fuel with a low oil content. Make sure you

use a model car fuel from a reputable manufacturer, such
as O’Donnell Fuels.

6. Avoid using old fuels in the engine.
7. Do not use a fuel with a nitromethane (often called nitro)

content over 20%.

8. Do not scratch the piston or cylinder sleeve. Avoid

jamming something into the exhaust port when removing
or re-installing the clutch or flywheel. Use a special tool
called the Ultimate Flywheel Wrench (DTXR1105) to
keep the crankshaft from moving.

9. Do not use silicone sealer on the engine joints. Silicone

sealer contains acetic acid, which is corrosive if it gets
inside your engine.

10. Do not allow any water to get inside the engine.This sounds

easy, but temperature changes can cause condensation
inside the engine. This is a good reason to use an after-run
oil. Store your engine inside the house, not in a garage or
shed where there will be temperature extremes.

BREAK IN

OCEDURE