4. Re-install the front suspension arms (38 & 39) to the front bulkhead
using the inner hinge pins (104) and the front hinge pin brace (50).
Secure the hinge pins by re-installing the two 2.5mm e-clips (S) onto the
ends of the two hinge pins (104).
5. Attach the front bumper (2) using the four 4-40x5/16" (B) screws.
REMOVE OLD SUSPENSION ARM
(Refer to Diagram 2)
1. Remove the four 4-40x5/16" screws (B) from the front bumper (2) and
set them aside.
2. Remove the front suspension arm (38 or 39) by removing the rear
2.5mm e-clip (S) from the inner front hinge pin (104). Slide the inner front
hinge pin out of the bulkhead and suspension arm.
3. Remove the 4-40x1/2" screw (D) that attach the bottom of the shock
to the front suspension arm. Rotate the shock out of the way.
4. Remove the front wheel.
5. Remove the two 2mm e-clip (R) from the front of the outer hinge pin
(95) and slide the outer hinge pin out.
The front suspension arm should be free from all of the other parts
at this point.
INSTALL THE NEW FRONT SUSPENSION ARM
(Refer to Diagram 2)
1. Install the front suspension arms (38 or 39) to the front bulkhead (51)
using the inner hinge pin (104). Secure the hinge pin by re-installing the
2.5mm e-clip (S) onto the end of the hinge pin (104).
2. Re-attach the front bumper (2) using the four 4-40x5/16" screws (B).
3. Attach the shock to the new suspension arm (38 or 39) by installing
the 4-40x1/2" screw (D).
4. Insert the outer hinge pin (95) through the front suspension arm and
front hub carrier (28). Secure the hinge pin by re-installing the 2mm
e-clip (R).
5. Re-install the front wheel and secure it using the 3/16" nuts (M).
REMOVE OLD UPPER PLATE AND SERVO BRACE
(Refer to Diagram 2)
1. Loosen the four 4-40x3/8"screws (C) in the front shock tower (49)
two turns.
2. Remove the four 4-40x3/4" screws (E) and the two 4-40x1/4" (B)
screws and remove the upper plate (52) leaving the servo saver
assembly in place.
3. Remove the two brass bushing (105) from the upper plate (52) using
a hex wrench included with the kit to pry them out.
4. Remove the two 4-40x3/8" screws (C) and remove the servo brace (56).
INSTALL THE NEW UPPER PLATE AND SERVO BRACE
(Refer to Diagram 2)
1. Install the new servo brace (56) using the two 4-40x3/8" screws (C).
2. Install the two brass bushings (105) into the new upper plate (52)
3. Install the new upper plate using the four 4-40x3/4" screws (E) and
two 4-40x1/4" screws (B).
4. Tighten the four 4-40x3/8 screws (C) in the front shock tower (49).
REMOVE THE OLD CHASSIS PLATE
(Refer to Diagram 1)
1. Remove the two 2.5mm e-clips (S) using a flat blade screwdriver from
the inner rear hinge pins (97) then, remove the hinge pins.
2. Remove the two 4-40x1/4" screws (A) to detach the rear chassis plate
(41) from the motor guard (3).
3. Remove the two 4-40x3/8" screws (C) that remove the rear chassis
plate (41) to the gearbox.
4. Remove the four 4-40x3/8" screws (C) to remove the rear chassis
plate (41) from the chassis (1).
The rear chassis plate should be free from all other parts at this point.
INSTALL NEW REAR CHASSIS PLATE
(Refer to Diagram 1)
1. Attach the new rear chassis plate (41) to the chassis (1) using the four
4-40x3/8" screws (C).
2. Install the two 4-40x3/8" screws (C) to secure the gearbox to the main
chassis plate (41).
3. Install the two 4-40x5/16" (B) screws that attach the rear chassis plate
(41) to the motor guard (3).
4. Attach the rear suspension arms (36 & 37) to the rear chassis plate
(41) using the two inner rear hinge pins (97). Secure the hinge pins by
re-installing the two 2.5mm e-clips (S) onto the hinge pins. Hint: First
position the e-clips in the grooves of the hinge pins using your
finger. Then, use a flat blade screwdriver to push the e-clip in place.
REAR CHASSIS PLATE REPLACEMENT
UPPER PLATE & SERVO BRACE REPLACEMENT
FRONT SUSPENSION ARM REPLACEMENT
Содержание Evader ST
Страница 3: ......
