DuraTech Industries HAYBUSTER CMF-590 Скачать руководство пользователя страница 19

Страница: 19 / 110

C M F - 5 9 0

O P E R A T I N G I N S T R U C T I O N S

1.5 Safety review section

BEFORE OPERATING

•

Read and follow all instructions contained in:

This CMF-590 operator’s manual

Tractor operator’s manual

Decals on the CMF-590

Note:

Additional copies of the above mentioned materials can be obtained from your dealer.

•

Allow only responsible, properly instructed individuals to operate your machine. Provide proper training

and carefully supervise inexperienced operators.

•

Use a tractor which meets the tractor requirement contained within this manual. Additional weights may

be necessary.

•

Make sure all bystanders and other workers are clear before starting the tractor and CMF-590.

•

Make no modifications to the machine unless specifically recommended or requested by DuraTech

Industries.

•

Check periodically for breaks or unusual wear and make any necessary repairs.

•

Securely attach to towing unit. Use high strength, appropriately sized hitch pin with a mechanical

retainer.

•

If required install P.T.O. safety chain, check local regulations regarding safety chain requirements.

•

Be sure that there are no tools lying on or in the CMF-590.

•

Because it is possible that your CMF-590 may be used in dry areas or the presence of combustibles,

special precautions should be taken to prevent fires and fire fighting equipment should be readily

available.

•

Do not allow anyone to stand between the tongue or hitch and the towing vehicle when backing up to the

CMF-590.

Keep sufficient distance away from electrical power lines.

WARNING: Electrocution is possible when running this machine during an electric storm or heavy fog.

NO SMOKING IN THIS AREA

DANGER! NO OPEN FLAMES

IN THIS AREA

Содержание HAYBUSTER CMF-590















































































































Результаты поиска

Содержание HAYBUSTER CMF-590

Отзывы:

DuraTech Industries HAYBUSTER CMF-590, Инструкция по эксплуатации и справочник по запасным частям, Страница: 19 / 110

Результаты поиска

Содержание HAYBUSTER CMF-590

Отзывы: