34
1 4 7 C D R I L L
O P E R A T I N G I N S T R U C T I O N S
4.11 Drilling with the Grain Drill
At this point the grain drill should be properly set up and adjusted according to the instructions in the preceding
sections.
Load the tanks with seed and/or fertilizer. Rotate the drive wheel by hand to make sure that the feed wheel shafts are
free to turn. This is particularly important if the drill was transported with fertilizer and seed in the hoppers.
Start the tractor, retract the cylinder completely, and begin drilling.
Periodically check for proper seed depth and feed rate.
When the seeding operation is finished, park the drill over a sheet of plastic, canvas, etc. Pull one of the cleanout side
control levers out to empty the remaining seed or fertilizer. Collect the seed or fertilizer. Repeat the procedure for the
other hopper.
4.12 SUGGESTIONS
When preparing to sow damp fertilizer that has been sitting in the tank for several hours, stir the fertilizer all the way to
the bottom to break up any blocks of fertilizer which have become cemented together.
The amount of fertilizer sown will vary with the moisture content and quality of the fertilizer.
4.13 REAR WHEEL SWIVEL AND ADJUSTMENT
Both rear wheels are designed to swivel 90° for the purpose of transporting drills endways. Adjusting bolts are
provided for aligning wheels in transport position as well as in forward position. Transport position is most critical for
tire wear due to hard surface roads and faster speeds.
CAUTION:
Transporting drills with seed and fertilizer in the tanks is not recommended. If drills
are moved any distance with seed or fertilizer in tanks, either in transport or field position, materials
will settle around feed wheels. Before starting to seed, operator should check with a wrench on drive
end of feed wheel shaft to make sure they are free to turn. Shaft may be turned either clockwise or
counterclockwise with openers in raised position.
WARNING
: Maximum transport speed should never exceed 20 M.P.H., and should be less where
conditions demand.
Содержание HAYBUSTER 147C
