To repeat the current track
• Press REPEAT ONE/DISC button until REPEAT ONE appears on the CD display and the currently
playing track will be played repeatedly until the stop button is pressed.
• Press
or
SKIP/SEARCH button with repeat function on, repeat can still skip through different
tracks of the currently selected disc.
To repeat the whole disc
• Press REPEAT ONE/DISC button until REPEAT ONE DISC appears on the CD display and the current
disc will be played repeatedly starting from the currently playing point.
• Press
or
SKIP/SEARCH button with REPEAT ONE/DISC function on, one can still search through
the whole disc, and the player may start playing from the selected point.
To repeat all discs
• Press REPEAT ALL DISC button until REPEAT ALL DISC appears on the CD display.
• Press on
or
SKIP/SEARCH button can make the player start playing from the newly selected
point of the currently playing disc.
• Press on DISC SKIP button can make the player start playing from the first track of the newly selected
disc. The
or
SKIP/SEARCH button can be used to choose a particular track on this selected
disc, the player will then start playing from that point.
To cancel repeat play
• Press either one of the REPEAT buttons until the word 'REPEAT' disappears from the CD display.
CD REPEAT PLAYBACK
REPEAT PLAYBACK - DURING PLAYBACK MODE
ATTENTION - If the CD player does not operate
properly
2. Slide the FUNCTION switch from ST.BY to CD.
1. Slide the FUNCTION switch from CD to ST.BY
(Standby).
USING THE REMOTE CONTROL CORRECTLY
• Point the Remote Control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be
degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 4 meters (13 feet).
REMOTE CONTROL (OPTIONAL)
1.
OPEN Button
2.
- SKIP Button
3. REPEAT Button
4.
+SKIP Button
5. DISC SKIP Button
6.
PLAY/PAUSE Button
7. STOP Button
USING THE CD STORAGE
• Open the CD Storage Door and insert the CD with the CD Box into the storage windows, maximum
to insert six CD.
CLEANING CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc from the center out with a cleaning cloth. After
playing, store the disc in its case.
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
IMPORTANT NOTE:
If an abnormal display indication or an operating problem occurs, disconnect
the AC power cord. Wait at least 5 seconds, then reconnect it. Before
transporting the unit, take out all the discs from CD tray.
MAINTENANCE
TO CHANGE REMOTE BATTERY
BATTERY REPLACEMENT
When battery becomes weak, the operating distance of the Remote Control is greatly reduced
and you will need to replace the battery.
NOTE:
If the Remote Control is not to be used for a long time, remove the battery to avoid damage
caused by battery leakage corrosion.
1. Open the battery door.
2. I n s e r t o n e C R 2 0 2 5 ( 3 V )
size battery.
ATTENTION
Take out the PVC sheet before operating
the Remote Control.
SPECIFICATIONS
TROUBLE SHOOTING GUIDE
The following checks will assist in the correction of most problems which you may encounter with your
system. Before going through the check list below, first check the following points.
CAUSE (AND REMEDY)
• Turn VOLUME clockwise.
• The headphones are connected. Disconnect them.
• The TV or VCR is too close to the stereo system. Separate the stereo
system from the TV or VCR.
• Wire the antenna.
• The disc is not placed correctly.
• Dirty disc.
• The disc is inserted upside down.
• The player is in the pause mode.
• Moisture condensation.
• CD is dirty or scratched.
SYMPTOM
No sound.
No sound from one channel or unbalanced
left and right volume.
Reversed left and right sound.
Lack of bass sound or apparently imprecise
physical location of musical instruments.
Severe hum or noise.
RADIO RECEPTION
The FM STEREO indicator flashes.
Distorted playback or sound loss during
CD playback.
EXPLANATION OF GRAPHICAL SYMBOLS:
WARNING
"WARNING: TO REDUCE THE RISK
O F E L E C T R I C S H O C K , D O N O T
REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL."
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
5 CD CHANGER
HOME STEREO SYSTEM
OPERATING INSTRUCTIONS
The lightning flash with an arrowhead
symbol, within the equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute an electric
shock to persons.
The exclamation point within the
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
RISK OF ELECTRIC
SHOCK DONOT OPEN
WARNING
CLASS 1 LASER PRODUCT
This product contains a low power laser device.
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK
DEFEATED.
AVOID EXPOSURE TO BEAM
Power requirements
AC ~ 120V 60Hz (USA/CANADA)
AC ~ 220V 50Hz (other countries)
AC ~ 230-240V 50Hz (Europe)
AC ~ 240V 50Hz (Australia)
AC ~ 110-120V/220-240V 50/60Hz (other countries)
Power consumption
15 W
CD PLAYER OPERATION
• Wire the antenna.
• Check the speaker connections of the inoperative channel.
• Check the speaker cord connection and speaker location.
• Check the speaker connection for proper phasing.
Play does not start.
Specifications and external appearance are subject to change without advance notice
due to continuous product improvement.
Printed in China
811-107091-010
GENERAL
Severe hum or noise.
CLASS 1 LASER
PRODUCT
2
3
4
1
5
6
7
'
%'
%
2
