background image

8. Secure the Right and Left Corner 

panels and (when installed) the Door 

Panel.  Use Anchor Angles supplied in 

Hardware Package.  Position the Angle 

fl

 ush to the inside of panel frame.  

Hold wall panel snug against post while 

installing Anchor Angle.

  See Drawing

.

9. Attach Angle to Panel with 

two (2) #8 x 1/2” self-drilling 

screws.  Drill 3/16” hole into 

deck and install #10 x 1” Hex Head Screw.

10. Attach Door Panel Angle on 

solid section of Panel.  

See Drawing.

After all Front Wall Panels are installed, lower the Roof to its 

fi

 nal position.

11. Install top bolt and wing nut through Trim Covers and Post.

Installing Side Walls Panels

1. For proper side walls installation, the front 

and back corners of each side wall must be plumb.  

Starting at the back of the awning next to the 

RV, drop a plumb line from the end of the Valance 

Track to the deck and mark that point on deck.

See Drawing.

To mark the front corner point, measure out 1-1/4” 

from the 

fl

 ange of the Post Bottom Anchor. 

Snap your chalk line between the two points on 

the deck.  This line marks the location of the 

outside edge of the Side Wall Panel.

2. Before installing the RV Wall Channel to the RV, 

attach the provided 1” x 1” Foam Tape to the side

of channel that will attach to the RV. 

3. Install Wall Channel by aligning it to the inside of 

chalk line on deck and plumb line on side of the RV.  

Wall Channel runs from deck to bottom lip of 

Mounting Rail.  Attach to RV with three #10 x 1-1/2” 

screws into wall of RV.

Page 3

Black Flashing

under Angle.

Содержание Dura-Breeze









Отзывы: